20 Most Recent Belkin (F5D7231-4) Wireless Router - Page 6 Questions & Answers

go to Belkin : Support : Setup Assistant for Routers

Please chack Your wep key.
after that tell me the status.

JAIN_IT

WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works

Disconnect the AC power.
Wait a few seconds.
Reconnect the AC power.
If the same problem appears, it's time to spend $20 to $40 to upgrade to a new "Wireless N" router (faster, stronger).

GO TO Belkin : Support

hi to reset password you have to reset the whole router, look on the back , there is a small hole, get a paper clip open it out, ( or something that will fit the whole will do) make sure router is on, press the reset button for 15 seconds and it will default back to factory settings, then to access it, just start your explorer, type in search bar, http://192.168.0.1 or 192.168.1.1 then at pop up screen for user name type admin, for password just type password and this will open the menu for the router, then you can put everything back the way you want it, with a password you can remember ....hope this helps

Power up the router, then press and hold the RESET button for 7 secs.
The default PW = blank (just press Enter)

Call you ISP provider.

1.Log into router. Using either 192.168.0.1 to 192.168.1.1 in a browser window that is ( internet Explorer or Firefox)
2. Verify wireless router name( on the computer) >>> ( on/off) ( router status window)
3.Note router name you are connecting to.
4.. Check the laptop do ipconfig /all to see current IP addresses.
5. Set the laptop up in the router by WEP KEY or MAC address. This set up in the "security tab" in the router. using 192.168.0.1 or 192.168.1.1 to access through a browser.
6.Note router name you are connecting to.
7. Move the laptop about 20ft away and try to log on to the internet.
This is for all routers to set up wirelessly.
8. check for firmware update at the manufacturers site for your model router
9. cell phones, cordless phones, digital TV's, can affect the data signal from a router. Also distance from the router can be a factor. If your router is in a basement place the router to a upper floor and center it in the room.
*****************************************************************
You will also need to configure your browser for the internet
1. for Windows XP here is the setup :
http://www.microsoft.com/windowsxp/using/networking/default.mspx
2. For Windows 7
here is the setup instructions: getting online and networking
http://windows.microsoft.com/en-US/windows7/help/networking-e-mail-getting-online

http://windows.microsoft.com/en-US/windows7/View-and-connect-to-available-wireless-networks

WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works

http://192.168.2.1

Check All your connection Reset your Router in the back you will see a little hole with a button press on it for 10sec.. Then got in your Sitting Control Pannel add and Remove ...Remove your Belkin software and re start your PC then re install your belking software for Any PC You may have a 4 hub conection ... So make shure your Modem are connected on the right Hub on your Router and the phone line to the modem Because See The modem tranmit is data to the router the transmit on any pc connected ony your Router ...good luck

Try to power cycle the router for about 1 min. If this will not work, try disabling all your anti virus and firewalls. If doesn't work, try 192.168.0.1 / 192.168.1.1.

do you have the network key for your network? Wireless Security ? if so you need to insert that in the other computer

check ur connection

s u can login to ur belkin router like connect a pc through hard wired >and login to router screen>and go to wire less settings>and u can see security under w/l> go to there>and select WEP and under phaseprace type any 10 digit no as password which u can easyly remember one>and save it>and reboot the laptop>and login to ur w/l n/w and it will ask for password>rate me if its help full thx...

How to secure the wireless network

Change the Name of the wireless network and change the password of the wireless network. So that they will not be able to get in to your wireless network.
You want to secure the wireless network.
Is there any computer connected to the router with the Ethernet cable?
If not then you will need to connect the computer to the router with the cable.
Check the IP address on the computer. Open the router set up page.
Once you open the set up page, you will find the option to make it secured

Click Here for step by step instructions

Sounds real odd, have you tried repairing permissions? in the application folder is utilities, in this folder select disk utility and select the hard drive, select repair permissions and give it perhaps 10 mins per 100 gigabites, it can take a while.