Top 10 Belkin (F5D5231-4) Router Questions & Answers

there are several reasons why this happens. dont use belkins utility use windows utility it will ask you if you right click the icon in the tray.

I’m happy to assist further over the phone at https://www.6ya.com/expert/james_1cb31da1bc8c6102

try HERE for info too

Try resetting the router, press the reset button at the back for 10 seconds, after that release the reset button and then unplug the power of the router, then wait for 10 seconds and then turn it back on.

After that try accessing the IP of the router 192.168.1.1 (if this did not work try 192.168.0.1,this varies on the model number of the router). Or follow the same steps you have done previously.

The default pin numbers are 0000 (zeros) or 1234.


If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

I have a Mac Pro and a Belkin F5D 7230-4 Router. The Mac links to the WiFi but will not go on to the internet. The Router works fine with a wired PC and other wireless PCs. I have updated the Belkin with the latest Firmware but it does not help. I have tried powering down the Router and Modem

Gmac

You can get the latest firmware here:
http://www.belkin.com/support/article/?lid=en&pid=F5D8236-4&aid=14396&scid=942

I don't think that it is a problem with your IP address settings.
I would disable all security temporarily, just to see if that makes a difference.
If you are using Windows Vista, take a look at this post and see if that could be one of the underlying problems.

If you have any more questions, just come back here and leave a comment - I'm happy to help.

this is because of the fact that your routers page was not logged out last time and now it shows duplicate administrator.
to remove this error please turn the power of your router off from at least 1 min and then turn it back on
Now open the webpage
and it will work

I ADVISE YOU TO PLEASE SET A PASSWORD TO YOUR ROUTER WEB PAGE

Thnx and i hope this helps
Please rate this solution

Try the following:

1. Make sure your PC is connected to the router directly and the LAN ports are lighting up
2. Reset the router
3. Reset the network adapter on your PC (or just restart the PC)

This should ensure that you are connecting on the LAN port.

Steps to setup Belkin wireless router f7d1301 v1 to a modem.

1. Make sure that your modem works by connecting the modem directly to your computer.
2. If the modem works connect the modem to the router then the router to your computer.
3. Log into your belkin router address (default) 192.168.2.1
4. Login with password (Before you can change any settings, you need to login with a password. If you have not yet set a custom password, then leave this field blank and click "Submit.").
1. Leave password section blank and click submit.
5. Go to Utilities > Restore Factory Defaults on left hand side navigation. (Using this option will restore all of the settings in the Router to the factory (default) settings. It is recommended that you backup your settings before you restore all of the defaults. To restore the factory default settings, click the "Restore Defaults" button below.)
1. Click the "Restore Defaults" (Router is rebooting seconds remaining.)
6. Login with password (Before you can change any settings, you need to login with a password. If you have not yet set a custom password, then leave this field blank and click "Submit.").
7. Go to WAN > MAC Address on left hand side navigation. (Some ISPs require that you clone (copy) the MAC address of your computer's network card into the Router. If you are not sure then simply clone the MAC address of the computer that was originally connected to the modem before installing the Router. Cloning your MAC address will not cause any problems with your network)
1. Hit Clone (Clone Computer's MAC Address)
8. Got to Wireless > Wi-Fi Protected Setup (WPS) on left hand side navigation. (Wi-Fi Protected Setup (WPS) is the industry standard method to simplify the security setup and management of the Wi-Fi networks. You now can easily setup and connect to a WPA-enabled 802.11 network with WPS-certificated devices using either Personal Information Number (PIN) or Push Button Configuration (PBC) method. Legacy devices without WPS can be added to the network using the traditional manual configuration method.)
1. Click on the drop down box next to Wi-Fi Protected Setup (WPS)and select Disable.
9. Got to Wireless > Security on left hand side navigation.
1. Click on the drop down box next to Security Mode and select 64bit WEP.
2. Change Key 1 to your phone number (2 digits in each box with area code included.) Your phone number is your password when setting up a wireless connection.
3. Apply changes.
10. Got to Wireless > Channel and SSID on left hand side navigation.
1. Click on the drop down box next to Wireless Channel > and select 6.
2. Click on the drop down box next to Extension Channel > and select 2 (if not already on it).
3. Click on the box next to SSID > and enter a new name (you can use any combo of letters or numbers). Write this down because it will be necessary to enter this information when connecting wirelessly.
4. Apply changes.

This is what I did on the phone when I spoke to technicalsupport for Belkin and it worked. I can't guarantee that this will work for youbut it's worth a try. If I missed any steps I am sorry.

DHCP Client list shows the list of devices currently connected to the Router

You cannot remove an IP Address of a device connected from this list ..

Regards
TOM