20 Most Recent Belkin (F5D5231-4) Router - Page 7 Questions & Answers


Hi i got your issue

Yes, it will not connect in your wireless notebook as this particular model of belkin router is a "wired router" it does not transmit any wirelless signal ......

If you want wireless connection you can look for the new model of routers from BELKIN

Thank you.....
With regards.....
Priya

Belkin... | Answered on Oct 03, 2010


From what I can tell you are using Mozilla Firefox Try using Internet Explorer if ip address id not valid it will tell you Internet Explorer cannot display webpage In order to renew ip address these are the steps you will want to take:
1. Ensure the equipment is connected correctly(Ethernet cord from modem to Internet port on router
2.Open network connections Win XP:Start/Run/Type ncpa.cpl
Vista/Win 7 Start/search bar/type ncpa.cpl
3.This will bring you to your network connections window
4.If using XP: Double click on wireless connection and hit the support tab. Ensure it is assigned by DHCP and the ip address should start with 192.
5. If Vista Or Windows 7 Right click on wireless conenction and hit properties. Uncheck version Internet Protocol Version 6
6. Click and Highlight internet protocol Version 4 and hit properties
7. ensure that it shows obtain ip address and obtain a dns server automatically
8.After go to Command Prompt (Win XP) Start/Run/Type CMD
Windows7/Vista:Start Start/All Programs/Accessories/Right click on command prompt and hit run as administrator then hit continue type in these commands.
1.netsh int ip reset reset.log
2.netsh int ip delete arpcache
3.netsh winsock reset
4.ipconfig /flushdns
9. Restart Computer hope this helps please rate thank you

Belkin... | Answered on Sep 30, 2010


1.Log into router. Using either 192.168.0.1 to 192.168.1.1 in a browser window that is ( internet Explorer or Firefox).
2. Verify wireless router name( on the computer) >>> ( on/off) ( router status window)
3.Note router name you are connecting to.
4.. Check the laptop do ipconfig /all to see current IP addresses.
5. Set the laptop up in the router by WEP KEY or MAC address. This set up in the "security tab" in the router. using 192.168.0.1 or 192.168.1.1 to access through a browser.
6.Note router name you are connecting to.
7. Move the laptop/ gaming module about 20ft away and try to log on to the internet.
This is for all routers to set up wirelessly.
8. check for firmware update at the manufacturers site for your model router and the gaming site for the proper ports for play.
You may just have lost connectivity with the server. Check your QOS ( Quality of Service ) in the rotuer settings to assure your wireless connectivity. Wireless gaming console are notorious for dropping connection. You also need to improve your antenna range. There are some DIY antenna templates on line if you do a Google search you will find a lot of them that will give you 20/30% gain.
9. cell phones, cordless phones, digital TV's, can affect the data signal from a router. Also distance from the router can be a factor. If your router is in a basement place the router to a upper floor and center it in the room.

Belkin... | Answered on Sep 28, 2010


Uninstall the belkin Setup and Router Manager software
It is very important to maintain a stable connection

WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works

Belkin... | Answered on Sep 26, 2010


WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works

Belkin... | Answered on Sep 26, 2010


WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )


=================================================
If not showing any wireless networks

Make sure the wireless switch is turned on in the computer
Let me know if it works

Belkin... | Answered on Sep 26, 2010


WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works

Belkin... | Answered on Sep 26, 2010


Hi,

>>>>Connect any of the computer to the router using a cable
>>>>Open the internet explorer page and in the address bar enter the numbers 192.168.2.1
>>>>On your left hand side you will be able to see Firewall
>>>>Click on firewall
>>>>It will ask for the password
>>>>Leave the password and click submit
>>>>Disbale the firewall
>>>>Click on apply changes

THANKS....
With Regards......
Vaishu

Belkin... | Answered on Sep 26, 2010


Take one Norwegian paper-clip, and straighten one end.
Turn the router off.
Insert the end of the paper-clip into the small hole in the back of the router, and hold it pressed-down for a few seconds.
This will reset the router to its "factory" settings,
including the default password.
Turn the router on, and configure it.

Belkin... | Answered on Sep 20, 2010


1. Step 1 Position your Belkin wireless G router.
Place your wireless G router in a wide open and central location. Don't connectthe power plug into the router, yet. Make sure your computer is turned off. 2. Step 2 Connect all the devices.
Find the Ethernet cable that connects your PC to the modem. Unplug the Ethernetcable from your PC and insert it into the wireless G router's WAN port. Youshould have an additional Ethernet cable that came with your router. Take thiscable and plug one end into one of the LAN ports on the router. Then connectthe other end to your PC's Ethernet port. 3. Step 3 Turn on your modem, router, and PC.
Plug the power plug adapter into the modem. Turn on the modem. It'll takeapproximately 30 seconds for the modem to boot up. Connect the power plugadapter to the router and the other end into a power strip or outlet. Like themodem, it'll take about 30 seconds for the router to boot. Turn on your PC. 4. Step 4 Verify lights are on for your devices.
Make sure the following lights are on for your router: power, WAN, and LANlight. If you don't see any of them lit, confirm these devices are turned on.Make sure the Ethernet cable connections are installed correctly. 5. Step 5 Install and configure software.
Use the setup wizard application to configure your Belkin wireless G router.Set up features, such as creating your password and setting up your time zone.Continue to follow the setup wizard so you can configure ?other settings.

Belkin... | Answered on Sep 20, 2010


Hey Chris

This kinds of issues are coming from the firmware of your router. So what you need to do is to upgrade the firmware of your router and make sure that you use a wired computer to do that. After the upgrade make sure that you reset the valet for about 1 minute. Just reconfigure the router so that it will be in sync with the modem. Usually with brighthouse, it will just go online right away.

Belkin... | Answered on Sep 18, 2010


Are you speaking about the password of the router or the password of the wireless network ?
If you don't know the password of the router , then you will need to reset the router and use the default password of the router.
Once you reset the router, you will need to reconfigure it.
If you are looking for the wireless password, you can find it on the set up page of the router.
You will need to open the set up page of the router.

Click here for step by step instructions

Belkin... | Answered on Sep 16, 2010


You will need to reconfigure the router.
Once you reset the router, it will come back to the factory default settings. Now you can reinstall the router.
You can do it manually without the CD also.
Make sure that your computer is able to go online through the modem.
If your computer is not able to go online through the modem then you will need to call ISP first.
If your computer is able to go online through the modem
then you need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.

Click Here for step by step by instructions

Belkin... | Answered on Sep 16, 2010


What has a router to do with a cd problem?Not enough clarification.

Belkin... | Answered on Sep 12, 2010


Hi Friend,
            Please follow the below link, where you can find step by step process for the Router Installation

http://www.fixya.com/support/r4364415-configure_brand_new_belkin_routers

Regards,
Aysaam

Belkin... | Answered on Sep 05, 2010


Go to Start->Control Panel->Network and Internet->Network and Sharing center->Manage network connections
You will find icons like local area connection, wireless connection and lot more. Just have one local area connection enabled and disable all other icons. Then run the setup

Belkin... | Answered on Sep 02, 2010

Not finding what you are looking for?
Belkin (F5D5231-4) Router Logo

533 questions posted

Ask a Question

Usually answered in minutes!

Top Belkin Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Jeffrey Groves
Jeffrey Groves

Level 3 Expert

573 Answers

Are you a Belkin Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Belkin Computers & Internet

  • Belkin Computers & Internet

Most Popular Question

belkin basic router not working

  • Computers & Internet
Loading...