20 Most Recent Canon PowerShot S2 IS Digital Camera - Page 2 Questions & Answers

Unfortunately this issue is most commonly caused by an electrical failure with the camera's power unit. Sometimes a hard reset will work, though I'm not sure if permanently.

Usually the solution is to call Canon's tech support and have the unit sent in for service. To give the reset a try however turn your camera on and immediately press and hold the Menu button for approximately 7 or 8 seconds (until you get a Reset Camera message). If you can get this far, do the reset and then power down the camera.

Then remove the memory card, the batteries and the date/time battery unit (a small rectangular door located inside the main battery well). Once all batteries are removed, turn the camera's power switch into the on position. Wait two minutes then press the power button as if turning it off. Then replace all batteries and the memory card.

Turn the camera back on and immediately set the time and date.
Turn the camera off and on a few times and take a few shots if possible. This works in about 25% of the time. If it doesn't and you have confirmed that the battery itselef is good (by placing it in another unit typically) then the camera will typically have to be sent in for a service repair.

Hope this helps.

Sincerely,
HeavyDLB

Here's the solution, I just had the same problem 1. take the memory card out 2.On the memory card there is a little switch (it will be the little tiny piece on the side of the card thats a different color) slide it up In Case You Still Having Problem Then Follow Us For On : Canon Support

Do not use alkaline batteries unless it is absolutely necessary. In some cases, alkaline batteries may have a shorter service life than NiMH. Alkaline battery performance is limited, especially at low temperatures. The use of NiMH batteries is recommended. Never use manganese (Zinc-Carbon) batteries in your camera. Check contacts of the battery and in the battery compartment of your camera. Dirty or oxidised contacts can be cleaned with a dry cloth. Never use sharp tools to clean contacts or anything in or on your camera. Always charge the battery before using it for the first time, or if you have not used it for a long period. 3 months is a very long period. Also check if the battery door is closed correct. Most cameras do have a switch connected to the battery door. If the switch does not work correct, it could be you can't switch on your camera. If you have a multi meter, you can check your battery. After charging the voltage should be higher (few tenths of a volt) than the voltage printed on the battery. If the voltage is slightly lower, you know thee will be not enough left when the battery needs to deliver some power.

Is the lens not coming out at all? did you check is the lens is blocked somehow?When a mechanical problem occurs, this can be a trigger for the camera to shut down, before something becomes (more) damaged. Did something happen the last time you used the camera?Was the camera switched of for a very long time?

Most camera's need this time to autofocus but if you half depress the button before the camera autofocus should do its job in advance. The picture takes immediately then.

Take it too a technician he can service it for you.

go there and you'll see you're not alone !
S2 IS Question: black screen in S1IS canon camera - DigitalCamera-HQ

It may be fixable, but it may be expensive. You also have the option to upgrade your camera through Canon's Loyalty program. I'd give them a call and find out what your options are before going out and purchasing a new camera.

Hi!
Try new batteries. If you already did it and it still says so, the power board has to be changed. You should contact your local Canon service center.

Hope this helps!

Tom

hi Cherushi, no need to worry, there are so many data recovery software available on net. so just download it and get your picture back.I hope you have not snapped more on that memory card after formatting. dont forget to tell me the result. I am waiting for your responce. good luck....

Dirty window in the viewfinder, clean with soft damp cloth with lightly soapy water. Or spectacle wipes

What type and size memory card? The S2 works with SD cards, 2GB or smaller. It will not work with higher-capacity SDHC cards.