Canon PowerShot SD400 / IXUS 50 Digital Camera - Page 9 - Answered Questions & Fixed issues

use the usb cable, the pc will see it as an external drive, pics will be in the dcim folder

check the card and see if there is a lock on the card and switch it off, if not, your pc software may have locked it, pop the card back to the pc, open the transfer software and check the settings

pop the card into a card reader, attach to pc. Pc will see it as external drive - then just transfer the pics as you would to any other device

No, place it in a hot place instead to evaporate the liquid, cell phones in the ferezer is for clearing the memory chip, not drying it out.

dust, use some compressed air to shift it. You will get some in a pc accessories store

search for your cannon model number on canons webpage and download the software. You should be able to use the camera via usb without it though. Your pc will see it as an external storage device. Your pics will be in the DCIM folder.

place your camera in a hot press, or where your boiler is, on shelf and it might dry out in a day or two, then try it again.

software has become corrupted, re install it

might seem silly, but have you checked the batterries?? The beeps usually signal a loss of power, if not check shutter is not jammed with dust particles, use compressed air to shift it.

check the lock on the card itself, you have accidently locked it with your finger, if not put it back on the pc and check if the transfer software has locked it in someway.

Hi, common problem with these, basically some dust particles have become trapped in the shutter or the rails on which the shutter runs on. A quich blast of pc dust cleaner or similar compressed air cleaner will shift it. No need to open any parts of the camera, f you do, you will void your warranty if it is still valid.

Download User Guide for Canon SD400 camera.

Let me know all above you said is in live view and if playback of previously taken pictures is good then its problem of defective CCD Imager Sensor in your camera Canon S400

Canon has announced free of cost repair on such problem for selected models and your camera model is in list.

For details click Canon CCD Advisory.
Regards,

found this guide on the net once, try it out and let us know what you think: " WARNING: this repair voids your warranty and may damage your camera. Perform at your own risk. The publisher of this site is not responsible for any damage you cause. This replacement is of medium difficulty. If you have ever ?built? a computer from parts, you are probably capable of it. If you are patient, orderly, and meticulous, you can probably do it. But you do risk breaking your camera even further, so don?t do it if you won?t accept that risk! Be carefully that you are grounded and thus do not harm the camera via static discharge. Google the terms ?grounding? and ?static discharge? if you need more info. I only performed this operation on a Canon SD300 / Ixus 40, but readers have reported that it is the same on the SD200 / Ixus 30 and on the SD400 / Ixus 50. Read all of the instructions before proceeding. Within each step, I don?t necessarily use exact chronological order. Tools: a small Phillips head screwdriver and a smaller flathead screwdriver (used for prying). Step 1. Ascertain what is broken. Symptom: your screen still glows with light, but shows crazy colors or a visible crack surrounded by crazy colors. Problem: your LCD screen is broken but your backlight still works. You need only purchase a new LCD screen. Symptom: your LCD does not glow. Problem: your backlight is probably broken. This didn?t happen to me, so I don?t give any further advice about this problem on this page. However, the information on this page will take you about 60% of the way to replacing the backlight as well, so it may be useful. Step 2. Order a replacement screen. UK: H. Lehmann's Ltd: +44 (0)1782 413 611 at a cost of 33 GBP (including shipping) US: Canon? +1 732 521 7230 / +1 800-828-4040 at a cost of around 66$ (including shipping) The part number for the SD-300 / Ixus 40 LCD screen (without backlight) is: ck9-1103 The part number is the same in the US & UK. I do not know whether the SD-200 / Ixus 30 LCD / SD-400 / Ixus 50 LCD part number is the same.. Step 3. Open the camera - Remove 6 screws in total: 2 from the left side, 2 from the right side, and 2 from the bottom. - Gently pry open the case - The plate covering the ?grommet? to which you attach the strap will fall off. So will the round grommet. Don?t worry about it. Step 4. Remove the screen & backlight assembly from the back of the camera - Remove the screw from the upper right corner of the backlight/LCD package. Note: this screw is of different size to those you have already removed. Keep it separate. - Be careful of the tongue extending from the bottom right corner of the backlight/LCD package. It?s very tiny and easy to miss. You want to be sure to slide it out, because it?s easy to just break the plastic into which the tongue slides. (I did. Not a huge crisis, but I wish I hadn?t!) - There is a tab on the left side of the backlight/LCD package. Pull it back slightly so you can lift the backlight/LCD package. (I used the flathead screwdriver to pry it off.) - You should now be able to lift up the backlight/LCD package. It will still be connected to the camera body via two ribbon cables. Step 5. Separate the LCD from the backlight - There are a number of fiddly plastic/metal tabs holding the two together. Just gently pry and poke until you have separated them. It?s a bit time consuming, but I can?t really give better instructions than these. - You should be left with the LCD totally separate from the backlight, but still connected to the camera via a ribbon cable. - The backlight should also remain connected to the camera via a ribbon cable. Step 6. Undo the LCD ribbon cable - The LCD ribbon cable extends under the bottom of the camera (actually passing under the tripod screw hole, which cannot be removed). It re-appears in the front of the camera and is connected to a socket. The socket is rather like a DIMM socket on a computer. It has a flat, black, clasp which is folded down to hold the ribbon cable in the socket. - Examine carefully the way the ribbon cable is attached to the socket. Note that it is pushed in entirely, so that the wider part of the cable (with two holes at either side of it) is flush against the socket. - GENTLY lift the clasp (I used the flathead screwdriver). It should swivel up and the ribbon cable should fall out. DO NOT YET PULL THE RIBBON OUT OF THE CAMERA. Step 7. Totally remove the LCD - Tape a long, narrow strip of paper to the end of the ribbon cable. This paper is to help you thread the ribbon cable of the new LCD back through the inside of the camera. - Note how the ribbon cable is threaded under the tripod mount to the front of the camera. Wiggle it around a bit, get a feel for it. Sliding the new one back through is a bit tough, so experiment with how this one fits and where it goes. - Gently pull the ribbon cable out from under the tripod mount, leaving the broken LCD screen now completely detached from the camera. Make sure to leave the paper threaded through the camera so that you can tape it to the new LCD?s ribbon cable and pull that one back through. - If you messed up with the paper, don?t worry. You can still push the new ribbon cable through: it just takes some wriggling and some time! Finishing. - You have now got to go through the process in reverse, installing the new LCD screen. - Threading the LCD ribbon cable back under the tripod mounting screw is tough. Just keep sliding it back and forth and exert pressure to push it through. It will go through, eventually. - As you connect the LCD ribbon cable, read the ?white screen? problem below, so that you do not suffer from it! FAQ 1. My screen just shows white or gray. (E.g. white screen, white display). What did I do wrong? A. The ribbon cable that connects the LCD to the circuit board was not inserted deeply enough. The end of the ribbon cable has a narrow portion, then a very small much wider portion with two holes at either end, then it narrows again. The very tip should be inserted into the "socket" deeply enough that the wider portion is pressed right up against the "socket." Physically, it cannot be inserted more deeply. It may help you to use two wooden or plastic toothpicks, one in each of the small holes at the end of the cable, to push the cable into the socket." If you feel like supporting the author of this thread, go to his website through this link: http://www.cl.cam.ac.uk/~jo262/broken_lcd_cracked_screen_canon_sd-300_sd-200_ixus-40_ixus-30.html Good luck

the beeps mean the lens can't be opened or closed. maybe something stuck or it's just failed?

Your camera creates folders on the SD card to hold the images. It puts about 100 images in each folder. (See page 111 in the User Guide.) When you erase images, it may only be erasing the images in one folder. But your computer still sees the images in the other folder(s). To completely erase all images, use the "Format" function (see pages 25 - 26 in the User Guide). To completely clear it, use the Low Level Format option. You can download the User Guide here.

The Canon PowerShot SD400 has no internal memory. All pictures are recorded on a memory card.

Hi, press the Display button 2 times to turn on the LCD display.
thank you

I replaced the memory card and this seemed to work OK.

I read a part solution on your web site about my Canon sd400 failing to start. The message gave a few free words about a micro swith in the cover. I couldnt find it! I called Canon tech and they said there was jo such switch. I packed up the camera and sent it off for a fix and a free firmware update. Probably going to cost $80. But I think it was the right thing to do!!
Ian