Canon PowerShot SD400 / IXUS 50 Digital Camera - Page 8 - Answered Questions & Fixed issues
Hello! I have a Power Shot SD400. I was wondering
The camera will only shoot up to one minute in "Fast Frame Rate" mode. You should press the function button and use the left/right buttons to switch it to "Standard". This will allow you to shoot until the card is full.
Dropped my canon powershot sd400, now it won't work fine
Hi there, there is two possibilities. The first one is to check the lens barrier covers at the front of the lens are opening correctly. If the front cap is dented in any way it may prevent them from opening fully when switching the camera on. If this is the case, you may be able to manually assist the cover by gently pushing them open with something soft like a cotton tip. This wont fix the problem but may temporarily allow you to use the camera. The other possibility, is that the shutter assembly inside of the lens has been damaged. If you gently shake the camera you may be able to see something shifting across the image on the screen or even when looking through the front of the lens itself. If this is the case you would need to have a service centre replace the lens for you. The same applies for the front barrier however that repair would be much cheaper. Best of luck!
Canon ixus 50 screen went into phsycadelic pattern
take it apart ie take the battery out, the memory card out and put it back together putting the battery back in last and try and turn it back on, if that does not help then I would get in touch with Canon and see if you can swap it or get it repaired via warranty if its still under warranty.
If you have had it less then 3 months you may be able to take it back to the shop where you got it from ( whether its online or physically at a store ) and see if you can get a replacement.
I bought a 4g SDHC card for my camera canon powershot sd400.
Well, first of all, I'm not exactly an expert on this, so please don't rely solely on my response.
It's possible that it needs an SD card, not an SDHC card. SDHC cards are high capacity, and some cameras just aren't able to use them because they're set up for the plain SD cards. Does it say what kind it needs in the manual? I think, if it's an older camera, I'm not sure what age exactly, they can't use SDHCs. Like I said, I'm not an expert, so you might want to get more info, if you can. Hope this helps.
Smoke fume from canon sd400
You should send the camera with the battery for service to find out if there is a defect on any internal circuit boards, or if the fault is actually the battery. There is no reliable way for you to determine this yourself, unless you have the proper setup and training to service these cameras.
Jerry G.
SD400 LCD Screen White after Replacement
There are a number of possible common faults that can cause the screen problem that you are describing.
It is possible that the new replacement screen is defective, or there is a defect in the ribbon cable, or the sockets are not making proper contact, or there is a cold solder connection at the socket or on the circuit board, or the driver circuits on the circuit board have a failure.
The service tech would try another screen, or ribbon cable (if changeable), or the circuit board to locate the defect. Once he finds the defective board, he will leave in the new replacement.
These cameras are serviced by modular approach.
Jerry G.
Upon turning on the canon
See this
link. Canon has issued a world wide service advisory about the CCD image sensor in several models of cameras. If they determine that this is the problem (and your symptoms indicate it is), they will repair your camera at no cost, regardless of warranty status.
Locked card
Pull out your memory card, and find the little gray slide switch, if it is away from card connection it is locked, slide switch (little gray slide switch) toward the card connection. This will unlock your memory card.
Hi. My Canon Powershot sd400
Hi!
You have to unlock your memory card. All memory cards have this small lock mechanism on the side.
Make sure that the slider is on the UNLOCK position. If it's already on the UNLOCK position and you are still getting the same error message, try to set it to LOCK, then set it back to UNLOCK position.
I hope that helps.
Good luck and have a nice day!
Camera problems
I have the same problem. i dropped it once and now every time i take a picture its all blurry. what can i do???
Powershot sd 400
have same problem with canon sd10. bought new battery and new charger, THIS IS A CANON HARDWARE PROBLEM I assure you
Not finding what you are looking for?