Brother Hl3070cw Hl-3070cw Color Laser Printer - Page 2 - Answered Questions & Fixed issues

Personally, I would just have found the correct USB Cable for it. The most likely reason would be that the Router details for the WiFi were not entered correctly. A quick search suggests it might be incorrect drivers. The windows version tends to be important in these questions. https://support.brother.com/g/b/downloadtop.aspx?c=ca&lang=en&prod=mfc685cw_us_as

Question edited for clarity. You need to Reboot everything first, Computer, Router and Printer and then Turn off Deep Sleep Mode.

Unable to print after the machine has entered "Deep Sleep"

Brother-USA https://help.brother-usa.com > answers > detail > a_id Reboot your computer and the power to your Brother machine. - Reboot the power to your router. - Attempt to print from another network-connected computer to ... Can I turn off Deep Sleep Mode?

1. Press Menu.
2. Press the UP OR DOWN ARROW to display General Setup. ...
3. Press the UP OR DOWN ARROW to display Ecology. ...
4. Press Sleep Time.
5. Using the dial pad on the touch screen, enter the length of time (0-90 minutes) the machine will remain idle before entering Sleep mode. ...
6. Press Stop/Exit.

Can I turn off Deep Sleep Mode? - Brother

Your Brother printer model 7535's drum may be getting toner powder on it for a number of different reasons. You might try the following troubleshooting steps: Make sure the toner cartridge is seated and correctly put in the printer by checking it. Toner powder may spread on the drum if the toner cartridge is not placed properly. Cleaning the drum may be necessary if it is unclean or has toner powder on it. A clean, lint-free cloth should be used to carefully wipe the drum after opening the printer and removing the toner cartridge. Avoid touching the drum with your fingers as this may leave a fingerprint that can affect print quality. Replace the drum: The drum may need to be replaced if it is worn out or damaged. For information on how to change the drum, consult the documentation or manual that came with your printer. Go at the printer's settings: Make sure the printer's settings are configured properly for the kind of paper you are using. Toner powder may spread on the drum if the printer is configured to use heavy or thick paper.

If your Brother GX-8500 electric typewriter is not typing after replacing the ribbon, here are a few things you can try:

1. Make sure the ribbon is properly installed. Ensure that the ribbon is installed with the correct side facing the platen and that it is threaded properly through the guides.
2. Check the print wheel. Make sure the print wheel is properly installed and that none of the spokes are bent or damaged. If the print wheel is damaged, it may need to be replaced.
3. Check the correction tape. If your typewriter has a correction tape, make sure it is installed properly and that it is not jammed or tangled. A faulty correction tape can cause typing issues.
4. Check the power supply. Make sure the typewriter is properly plugged in and that the power outlet is functioning. You can also try plugging the typewriter into a different outlet.
5. Try resetting the typewriter. Some typewriters have a reset button or combination of buttons that can be pressed to reset the machine to its default settings. Refer to the user manual or contact Brother customer support for instructions on resetting your specific model.

If none of these solutions work, it's possible that there may be a more serious issue with the typewriter that requires professional repair.

If you have a stuck toner cartridge in your Brother TN630 printer, here are some steps you can try to remove it: Turn off your printer and unplug it from the power source. Open the front cover and carefully remove the drum and toner assembly. Locate the release lever on the side of the toner cartridge and push it down. Try to gently pull the toner cartridge out of the drum unit. If the toner cartridge is still stuck, try gently wiggling it back and forth while pulling it out. If the toner cartridge still won't come out, try using a pair of pliers to grip the cartridge and pull it out. Be careful not to damage the cartridge or other parts of the printer. Once the cartridge is removed, clean any debris or residue from the drum unit and the cartridge itself. Reinstall the drum and toner assembly back into the printer, making sure it is securely in place. Close the front cover and plug the printer back in. Turn on the printer and test if it is working properly. If these steps do not work, it may be best to contact Brother's customer support for further assistance or to schedule a repair.

Yes, the Brother MFC-2690DW can scan photo slides. It is capable of scanning a range of documents and media, including photos and slides, in both black and white and color. The Brother MFC-2690DW also comes with a range of software which can be used to automatically adjust the quality of the images and scan them into digital formats such as JPEG or TIFF. Additionally, you can use the Brother MFC-2690DW to scan and digitize slides directly into a computer or other digital device, allowing you to easily store and share your images.

If your Brother DCP-1510 printer is in sleep and stack copies mode, you will need to wake it up in order to print your document. To do this, simply press the power button on the printer and it should wake up. Once the printer is awake, you will be able to print your document.

They have a 877# you can call for assistance. https://www.brother-usa.com/support/wp1400d Best to you

RROR 49 se refiere a la tensi?n de la unidad de impresi?n. Puede que solo necesite que los cables planos que conectan la cabeza a la placa base se vuelvan a conectar, pero tambi?n podr?a ser necesario un servicio t?cnico. Para solucionar el error 49 en una Brother DCP-T300, desconecte la m?quina de la toma de corriente. Deje desconectado durante un minuto completo. Despu?s de un minuto, vuelva a conectar la m?quina. Si el error "Unable to init 49" desaparece, imprima una hoja de comprobaci?n de calidad de impresi?n. Si el error persiste, su m?quina necesitar? servicio t?cnico. Antes de acudir a las opciones de garant?a, se recomienda transferir sus faxes y el informe del registro de faxes. Si necesita ayuda para solucionar el error 49

To replace the ADF pickup/roller assembly on a Brother MFC-L8900cdw printer, follow these steps:

1. Turn off the printer and unplug it from the power outlet.
2. Open the automatic document feeder (ADF) cover and remove any paper from the feeder.
3. Locate the ADF pickup/roller assembly. It is located underneath the ADF cover and consists of a set of rollers that are used to feed paper into the printer.
4. Use a small screwdriver to remove the screws that secure the ADF pickup/roller assembly in place.
5. Carefully lift the ADF pickup/roller assembly out of the printer.
6. Install the new ADF pickup/roller assembly by aligning it with the mounting holes and securing it in place with the screws.
7. Close the ADF cover and plug the printer back in.
8. Turn the printer on and test the ADF to make sure it is functioning properly.

If you are having difficulty replacing the ADF pickup/roller assembly or if the problem persists after replacing it, it may be necessary to have the printer serviced by a professional. A technician will be able to diagnose the problem and determine the necessary repairs.

Check out the help in the link. https://www.google.com/search?q=Brother+5460cn+error+51 ..

Here are some steps you can follow to set a static wireless IP address for your Brother HL-2170 printer:

1. Press the "Menu" button on the printer's control panel.
2. Use the arrow keys to navigate to the "Network" option and press "OK".
3. Select "WLAN" and press "OK".
4. Select "Configure Network" and press "OK".
5. Select "Manual Setup" and press "OK".
6. Select "IP Address" and press "OK".
7. Use the numeric keypad to enter the desired IP address for your printer. Make sure to use a unique IP address that is not already in use on your network.
8. Press "OK" to save the changes.
9. Press the "Back" button until you return to the main menu.
10. Turn the printer off and on again to apply the new settings.

After following these steps, your printer should have a static IP address that will not change. You may need to update the settings on your computer or other devices to use the new IP address in order to print.

ck here.. https://www.manualowl.com/m/Brother%20International/9870/Manual/274629?page=177#manual or here..... https://printcopy.info/index.php?mod=erc&brand=Brother&model=MFC9870 best to you

In this link https://techsupportexpert.com/steps-to-fix-brother-printer-error-78/ ..

Videos on it for 9840 and what it looks like. https://www.google.com/search?q=brother+4040+laser+printer+polygon+motor+replacement ..

Hi, Please restart your type writer machine before trying your procedure again. Then, please double check that pressing alt + m is a correct procedure based on your product manual. If so, and you can continue to have this issue, please reference the troubleshooting manual before sending in the type writer for repair with brother. Thank you.

Have a look on the brother web site.

It is very common to encounter Brother Printer in Error State Windows 10 with any Printer, the same is the case with the Brother Printers and scanners. They also confront the error due to some reasons. These error codes indicate some specific issues with your printer. Brother Printer in Error State Windows 10 problem is an error usually displayed when the printer is jammed, low in paper or ink, the cover is open, or the printer is not connected properly, etc. Here some applicable solutions to fix this error. Method to fix Brother Printer In Error State Windows 10:- 1. Check the connection and restart your devices. 2. Update or reinstall the printer driver. 3. Contact the printer manufacturer. The Brother Printer In Error State Windows 10 is a very harmful error this error is very annoying. If you want a full solution to this error check this blog and follow the steps given in the blog.

Access the internal maintenance mode by pressing the Menu/Set button, then press * 2 8 6 4 within 2 seconds. This should put you in the maintenance mode menu. Enter 80, then scroll down with the arrow down (round) key. You'll find an entry listed as purge count. If number is over 6000, enter 2 7 8 3. This will reset the purge count value. Then the printer will restart, try this step by step.without missing any thing. thanks

Your Brother printer can be offline, most probably when it is not set as default printer on your computer. Let's take a look at the steps on how do I get my brother printer back online. First, right click on the printer icon in your computer. Go to what's printing and click on printer. Then, remove the check mark in front of use printer offline. The status of your printer would be now back online and ready to print. https://connectmyprinter.com/how-to-fix-brother-printer-offline-error/