Top 20 D-Link AirPlus DI-614+ Wireless Router Questions & Answers

junk it and get something that doesn't impede the speed

Either the router does not support WPS-with-PIN, or it is printed on the bottom of the router.

Start from the beginning, is it plug into a working AC outlet?, is the plug fully into the AC jack?, wiggle the plug at the AC jack, it may be a bad AC jack connection due to damage. This may help: http://www.dlink.com/us/en/home-solutions/support/product/-/media/Consumer_Products/DI/DI%20614plus/Manual/DI614ManualUS.pdf If all fails ,replace wireless device.

go to the d-link web page. I have had excellent support from their technicians in the past

If you forgot the router password, you will have to do a hard factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can set-up form scratch.

login to your ISP

I believe the pick up signal for your internet connection should be wired, the D-Link device will create it's own local home network for you.
I don't think the D-link can connect to another network Wireless, only create it's own.

Do you need to connect to a wired or wireless 'appartement' network?

1. Turn off the router

2. Locate the Reset button on the back of the router.

3. Use a paper clip to press the Reset button and power on.

4. Hold for about 5 seconds (don't hold too long) and then release. (Or, release when M1 and M2 flash at the same time.)

5. After you have completed the above steps, the router will be reset to the factory default settings

Then open up the browser and type in 192.168.0.1

It will ask you for a username(leave it blank) and password (admin).

Once you are in the router setup, you can setup a new password. I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

well just reset your wireless router and configure it again....

The factory default User name is admin and the default Password is blank (empty). It is recommended that you change the admin password for security purposes. Please refer to Tools>Admin to change the admin password.

You need to download the user manual. ftp://ftp.dlink.com/Gateway/di614+/Manual/DI-614+_manual_06292005.zip

You should download and read manual pages covering Using the Configuration Menu that begins on page 10. Securing your wireless is detailed starting on page 12 for WEP, page 13 for WPA (only if you have a Radius Server - most likely not) and page 14 for WPA-PSK.

Nearly all devices support the older WEP encryption method. The downside is that it is easily defeated with software in under 10 minutes. A much better, more robust method is WPA-PSK. It can not be defeated (yet). If you choose WPA-PSK, any device that you connect wirelessly to this router MUST support WPA-PSK as well, otherwise it will NOT be able to connect.

I hope this helps and good luck. Please rate my reply, thanks.

Hi. There are 2 versions of this router Go here http://www.dlink.com/products/?pid=DI-614%2b&tab=3 and click on your model. (reg or B revision) This will allow you to download any available resources like users manuals, any software or firmware updates etc..

is your Router old? it could be wearing down. have you refreshed your Ip address and is there concrete metal anything that would interfere etc

ftp://ftp.dlink.com/Gateway/di614+/Manual/DI-614+_manual_06292005.zip Download the manual..

sounds like the router and modem arent talking what kind of internet connection are you using and have to tried accessing the internet with the ethernet cord that runs from the modem to your computer. if you cant access the internet with that direct connection to the modem you might have a bigger issue

Connect a LAN cable from the D-Link to your laptop/computer'sLAN port, open the browser on your laptop/computer and enter the D-Link'sconfiguration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop with the router's wireless settings.
To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Hello,

yes the web settings are open and wep and then your key. but note that wep is not secure at all, it takes around 10 to 20 minutes to get your networks password by being nearby your house while your surfing the network and you will never know a thing.

As a test, set it to WPA and see if the apply button starts working If not, restart your computer to make sure thats not the issue, if the issue persists reset your router, and if the problem still sticks restore factory defaults from the router or re do the update.

get back to me on how you get along with it after you have followed the above.

Thanks,
Ekse

The factory default User name is admin and the default Password is blank (empty). It is recommended that you change the admin password for security purposes. Please refer to Tools>Admin to change the admin password.
You need to download the user manual. ftp://ftp.dlink.com/Gateway/di614+/Manual/DI-614+_manual_06292005.zip
If the password has been installed, and you cannot remember it, look for a recessed button usually located by the power input plug and press and hold it for about 10 seconds. Then pull the power out and plug back in (to restart) This action will wipe all settings back to factory. Which means you will have to setup wireless password and any ISP (Internet Service Providor) settings needed to access your service.

In order to get your router back to the original settings, you must push in the reset button (usually on the back of the router) for somewhere between 10 and 30 seconds depending on the router. You may need a pin or something small to push in the button, because it can be recessed. Once you have reset the router, the username and password will be changed to the defaults, admin and password, respectively. One thing you must remember is that resetting the router will change all of the router settings back to the factory settings. This means you will lose all of the changes you made since you got the router. Make sure to write down any things you've changed, so you can change them back after the reset. Also, I recommend updating to the latest firmware after the reset.

There a great article at General Router Setup.
If you need more help post back!
Thumbs and testimonial are welcome!