20 Most Recent D-Link AirPlus DI-614+ Wireless Router - Page 8 Questions & Answers

is teh ip assigned static on teh pc or in the router

if its in teh router then login to the router and home and click on wan and change it to Dynamic IP Address and click on apply and reboot thats it if its working rate me solved

Hi, On a similar model, the advertised range is anywhere from 50-100 meters outdoor or open air. Inside the house or within the office, the walls, doors, drapes, furnitures etc obstruct the signal and brings down the range to less than half. What we have tried to improve the signal range: 1. Install the AP/Router high up not just on top of a closet or cabinet but really high, about a foot from the ceiling; 2. Approximate the very center of the various locations of the laptops and install the AP/Router there; 3. Disabled and did not use security WEP, WPA but turn MAC Filter on; 4. Use an external hi-gain omni antenna; 5. Install a second similar unit at the farthest coverage and run it as a repeater; 6. Replace the AP/Router with the new N type (which again claimed to be 4X wider and 12X faster) which made us go back to step 1. It's a love/hate experience and we ended installing more repeaters. But it works. Hope this give you an idea or two (but hopefully not the frustration nor the headache). Post back how things worked out your end. Cheers

usually new routers (not configured) can be access via the default ip address... 192.168.0.1.

but it would be better if you look over your manual on how to properly access your router. cheers.

Sounds like it's toast. Not much you can do except replace it. Sorry.

change the mode to mixed>and disable any security>and changed channels use only 11>and 1>and reboot>and rate me solved if its helped>

This is because they are on differing addresses.. you may have to "Bridge" the network connections.. the Wifi is probably on 10.0.0.* and the Wired is on 192.168.0.* you need to make a "Connection" between the two so the can "See" each other. You will find how to do this in ya manual. Here is a link to help.. www.microsoft.com/technet/community/columns/cableguy/cg0102.mspx I "Googled" how to bridge wireless & wired networks router xp So if ya get stuck try a "Google" ... :)

If your ISP is not having problems typically a router will just need a reboot to make it start working again. Simply unplug the power cord to it, wait 10-15 seconds, plug back in and try it again.

What happens if you connect one of the wireless machines with an ethernet cable? Any chance you have a Firewall of AV program blocking port 25 on these machines? Have you tried Safe Mode With Networking? I'm sure you realize that is most often caused by the ISP blocking Port 25, but I assume they would have told you so if this was the case.

Make sure you disable or uninstall any PPPoE software such as WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet. Do not disable until you´ve downloaded the firmware in Step 1. Please make sure that your modem is not also a router. If it is or you do not know, please contact your ISP and change the modem to Bridge mode. Note: In some areas, BellSouth and Verizon may not use PPPoE. Step 1 Upgrade to the latest firmware. Step 2 Take a paperclip and perform a hard reset. With unit on, use a paperclip and hold down the reset button on the back of the unit for 10 seconds. Release it and the router will recycle, the lights will blink, and then stabilize. Step 3 After the router stabilizes, open your web browser (Internet Explorer, Netscape, etc), enter 192.168.0.1 into the address window, and hit the Enter key. When the password dialog box appears, enter the username admin and leave the password blank. Click OK. If the password dialog box does not come up repeat Step 2. Note: Do not run Wizard. Step 4 Click on the WAN tab on left-hand side of the screen. Select PPPoE. Step 5 Select Dynamic PPPoE (unless your ISP supplied you with a static IP address). Step 6 For Earthlink users, under the username field enter ELN/[email protected] and your password, where username is your own username (some Earthlink users may not need the ELN/ in front of username). For SBC Global users, enter [email protected]. For Ameritech users, enter [email protected]. For BellSouth users, enter [email protected].** For most other ISPs, enter username. **Note: In some areas, BellSouth may not use PPPoE. Ameritech users: If you cannot connect, try entering just the username (without the @ameritech.com) and then put ameritech.net in the Service Name box. Step 7 Maximum Idle Time should be set to zero. Set MTU to 1492, unless specified by your ISP, and set Autoreconnect to Enabled. Note: If you experience problems accessing certain websites and/or email issues, please set the MTU to a lower number such as 1472, 1452, etc. Contact your ISP for more information and the proper MTU setting for your connection. Step 8 Click Apply. When prompted, click Continue. Once the screen refreshes, unplug the power to the D-Link router. Step 9 Turn off your DSL modem for 2-3 minutes. Turn back on. Once the modem has established a link to your ISP, plug the power back into the D-Link router. Wait about 30 seconds and log back into the router. Step 10 Click on the Status tab in the web configuration where you can view the device info. Under WAN, click Connect. Click Continue when prompted. You should now see that the device info will show an IP address, verifying that the device has connected to a server and has been assigned an IP address.

Step 1. Create a Folder on the Desktop Screen: From a blank spot the Desktop Screen, press and hold the Control key on the keyboard and click the mouse button. Release the Control key, click New Folder, and name it firmware. Step 2. Retrieve Firmware from Website: Click link below and download file to the folder created in step 1. Download DI-604 Firmware here - http://support.dlink.com/products/view.a... Download Di-614+ Firmware here - http://support.dlink.com/products/view.a... Step 3. Upgrade the Firmware: A. From the Main Desktop Screen, launch Internet Explorer or Netscape. B. Type 192.168.0.1 in the Address bar and click Go. C. For the User ID, type admin and click OK. D. Click Tools on the top and then click Firmware on the left side. E. Click Browse>Desktop>firmware, double click di6xx_firmware_203.bin and click Apply. Wait for approx. 15 seconds or until the M2 light stops flashing on the DI-6xx unit then click Continue. F. This takes you back to the Tools page. Check the Current Firmware Version on the Tools page to confirm that the firmware loaded successfully.

You can find the details of the operator and the state they belong to .the operators wont reveal the address and name of any mobile numbers only higher officials can only get those information.
In order to trace the operator name and state you can try this link
http://www.indiatrace.com/trace-mobile-number-location/trace-mobile-number.php

I hope this will help you if it does do rate the answer
Thank you
regards
lalith

I am sure it is now toast and you cannot downgrade if the wrong firmware has been installed. I would ask D-Link.

https://www.youtube.com/watch?v=zKeXtyUMKjA Check out this video it might help you with your issue.

Please open router page and go to advanced just like in this emulator. http://support.dlink.com/emulators/wbr2310/adv_network.htm

try changing the channel number from auto to a channel number 2 or 3 higher than the lowest channel number.' do this by logging into the d-link dsl 2640

access violation in module Uimain.exe at address oo6F6AB6 read address 000002EC

Ethernet/USB Print Server it is for even windows 98 (OMG ) page 7 is setup. NO OS stated by you, at all. why:? page 3 is OS compat. after reset the default address is 192.168.0.10 5volt power pack is NOT OPTIONAL. 1998 what did you read the free manual yet. the last page shows printer compatibility list, does your match? where would you find a printer that old working now. crickets...??? my guess is 2003 year made. XP first release is that. one manual for it stamped 2003 so is 17 years old relic fodder for sure, recycle it is best. first hit https://eu.dlink.com/-/media/consumer_products/dp/dp-300u/datasheet/dp_300u_datasheet_en.pdf RTM ! no 17 year old printer works today, not really.

the manual is free , at dlink dot com you push the reset button for long time per manual 15sec (iirc) the release it and now all defaults are set. per the manual, google dir-655 manual. easy as pie if you just read the manual.

There's a reset button on the back of the router, it's a small button that you can press using a paper clip. Press it for 15 seconds to reset it.

Reset 1:
Press the reset button for 15 seconds at the back of the router while the router is on.

Reset 2:
Press the reset button for 15 seconds while the router is on after 15 seconds unplug the power cord while holding the reset button then count another 15 seconds and release the reset button. Then plug the power cord back in.

Reset 3:
Press the reset button for 15 seconds while the router is on after 15 seconds unplug the power cord while holding the reset button then count another 15 seconds and plug the power cord back in while the reset button is plugged in and count another 15 seconds release the reset button.

Hope this helps.

You can get best d-link router support phone number at Toll Free Number ( 1-877-769-0969 ). D-link router Tech Support number ( 1-877-769-0969 )