20 Most Recent D-Link AirPlus DI-614+ Wireless Router - Page 3 Questions & Answers

You can get the manual on the link below. The whn line is the line from the modem.

http://www.ec-es.de/download/di614%2B_manual_202.pdf

Good Luck please rate 4 thumbs up and please leave a testimonial

If you have resetted your device frequently then the reset button should have worn out. Just replace the Reset button with a new one that should be fine.

otherwise you will have to log on to the router using the ip address of the router where you will find a link to reset the device to factory setting. just click it. It is the same as pressing the reset button.

To hard-reset the D-Link AirPlus DI-614+ to Factory Default Settings, do the following:

Turn off the DI-614+

Locate the Reset button on the back of the DI-614+

Use a paper clip to press the Reset button.

Hold for about 5 seconds and then release

After the DI-614+ reboots (this may take a few minutes) it will be reset to the factory Default settings.

Thanks for choosing FixYa, If you find this helpful please vote and comment.

simply enable the encryption in the admin panel, http://www.findpdf.us/search?q=wifi&submit=Search

You could setup two different profiles, one for each wireless router.
Configure your home wireless router with a different SSID and encryption setting to the office wireless router.
Then configure the wireless card in your laptop with two different profiles, one for the office wireless router and one for the home wireless router. When you want to use the home or the office wireless router, just call up the profile you require.

Are you trying to set up the router.
You can do it manually without the CD.
Make sure that your computer is able to go online through the modem.
If your computer is not able to go online through the modem then you will need to call ISP first.
If your computer is able to go online through the modem
then you need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.
Click Here for step by step by instructions

By default, the WLAN on your router is enabled. This is the setting that will give wireless computers wireless internet connection.

no setup cd needed. after connecting to a PC, open browser and type in 192.168.0.1 or perhaps 192.168.1.1 -- when the router displays it will ask for a password. if you had one and can't remember it do a hard reset to return to factory settings. then log into it leaving the username blank with the default factory password. many times that password is admin -- download the owner's manual that will have the default password and instructions and explanations for the settings, including how to do a "hard, factory" reset for free at the manufacturer's website. try the help, support, or download sections. the drivers are there too.

1.Log into router. Using either 192.168.0.1 or 192.168.1.1 in a browser window that is ( internet Explorer or Firefox)
2. Verify wireless router name( on the computer) >>> ( on/off) ( router status window)
3.Note router name you are connecting to.
4.. Check the laptop do ipconfig /all to see current IP addresses.
5. Set the laptop up in the router by WEP KEY or MAC address. This set

up in the "security tab" in the router. using 192.168.0.1 or 192.168.1.1 to

access through a browser.
6.Note router name you are connecting to.
7. Move the laptop about 20ft away and try to log on to the internet.
This is for all routers to set up wirelessly.

Hi,

Please access the web interface of the router and confirm the security key. Also, you can try to change the security key. It can be a possibility that your computer is not synchronizing properly with the current security settings.

If you find that you are putting the right security key then please change the security type to wep 64 bit or wep 128 bit and configure a new key. Also, change the SSID or the network name and try to connect.

In case of any issues please let me know which windows you are running and the security settings on the router.

Thanks,

Rashish

Start by looking at the lights blinking on the router. Which ones are blinking? How are they blinking?

WHen you've assured yourself of that the router is working properly, open a command prompt (windows button + R) and then type CMD, You will now get a command based interface, type ipconfig /all - And try every single adress that pops up in your browser.

try first your electronic store, be aware that sometime is cheaper to buy new router than power supply for old one... i would suggest try first in some friendly computer store, where they may have similar adapter for symbolic penny.

do bear in mind that this product is out of production since about 2004... and no support for it since 2007/2008

it uses 5V DC/2.5A power supply

1. this error is not recognizable.
But here is the D-link site for updating your firmware for the DI-614
this may resolve your issue.
http://www.dlink.com/products/?pid=DI-614%2b
2. You also may want to check the status of you router by logging into it and checking the "status" page (192.168.0.1)
User : admin
No password unless specified
This will tell you a lot as to what the router is doing and not doing.

This would be the router itself not agreeing with the computers ethernet card. I would have a look at firmware first and see if that does not put a stop to your issue, you mentioned you tried a diffrent cable and direct connection was fine then the router is the issue. I would try to firmwar eit first if that does not work I would try a diffrent router at this point.


thanks and please do be considerate and leave positive feedback and ratings. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

1. If you have a modem, connect the modem to the router(make sure modem should be connected to the port on which LAN, Internet, WAN is mentioned. It would be a separate one port on the router) and router to the computer.
2. Insert the disk that came with the router, inside the computer.
3. Follow the on screen instructions.
4.No, connect to the wireless.

If you are referring to a cable modem then you may be talking about using both the USB connection and the Ethernet connection. They will not work simultaneously. But if you have a router and branching your connection, then there should not be any problems. Just make sure that when you are accessing the Internet through a router that you make sure that your router's IP address can access the internet after that you leave your computer's IP at Detect Settings Automatically, it works for me

You need to configure your router.
For that Connect your router to computer with ethernet cable then you can access it with following default link.
http://192.168.0.1
or
http://192.168.1.1
If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it.
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank.
Then you can see configuration page of router.
Click on WAN settings and set those settings as your internet service provider settings.
Enable DHCP if you want to get ip from router.
Clickon wireless settings enable wireless then enable WEP Security then add WEP code .It is your password to connect wi fi.Then save settings and restart router.
Then you can connect your wi fi network with that code.
Then in vista make sure wireless lan driver installed then right clickc on wi fi icon and click on view available wi fi then you can connect it.
Let me know if you need further assistance.
Thanks for using FixYa.

Make sure that your computer is able to go online through the modem.
If your computer is not able to go online through the modem then you will need to call ISP first.
If your computer is able to go online through the modem
then you need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.