20 Most Recent D-Link AirPlus DI-524 Wireless Router - Page 3 Questions & Answers

Some don't have a button

D-Link ManualIf you have forgotten your password details, you just need to reset the router. this will enable you to togon with the default details. (see manual)

there is a pin hole present on back side of modem reset button press it for 5 seconds and ur modem is reset all setting and passwords

the wan should always be blinking
if your computer screen is blinking there is something wrong with the screen If you need further help, reach me via phone at https://www.6ya.com/expert/david_eb7ea98642566cc6

Apple explains how to unlock the iPad if you no longer remember the passcode or password in the manual for each device (on pages 44 and 146 of the original ipad manual to be precise) as well as on the company support site or visit http://support.apple.com/kb/ht1212

How to router wireless password

the default password is blank for that router. the username is adminIf you need to reset your router to the default (erases all data) Perform a 30-30-30 reset which is: Hold the reset button for 30 seconds, (don't let go until you have performed all steps and have held the button for at least 90 seconds total).After the first 30 seconds, unplug the power cord from the router.Wait 30 seconds while still holding the button. Plug it back in, wait 30 more seconds, and then let go, wait NO LESS than 5 minutes(really, go make a coffee, don't interrupt this process) and then try to log in again.

after when i open the browser and open the administrative page what should i do






/

Have you done any firmware update on the D-Link? Remove the ISP Ethernet connection. Pull the plug on the D-Link, wait 30 seconds or so, plug in, wait for selftest, reboot computer. If that fails, reset the D-Link to default settings. Reconfigure the SSID and Security Key. If all fails , the device may be bad.

If you are using one box (or modem/router) only, when your computer says media disconnected, it means that your computer does not detect your modem. 
You can try unplugging and replugging the ethernet at the back of your computer or laptop. make sure that the light on the ethernet port is lit up (especially for desktops, not sure about laptops though).
You can also do the same process with the ethernet cable from your modem/router. if your modem/router has other ethernet ports in it, try to connect it to other ports as well. If your computer still says media disconnected, try purchasing or borrowing a new ethernet cable. 
Also make sure that your ethernet adapter is working properly and that media disconnected follows after ethernet adapter local area connection and not wireless connection.
Hope this helps!

If the default password on the D-Link has been changed then - To reset the D-Link back to the default settings - Press and hold the RESET button at the back of the router with the power ON until the LEDs flash at the time the release the RESET button. (firmware version was 3.00, and upgraded to 3.05) Connect a LAN cable from the D-Link to your laptop/computer's LAN port, open the browser on your laptop/computer and enter the D-Link's configuration URL.. http://192.168.0.1 The default login = admin The default PW = blank (just press Enter) You can now change the default admin password. You can now configure the wireless settings. (WPA or WPA2 encryption to protect your wireless network and Internet from unauthorized access). Now configure the wireless card in your computer/laptop with the router's wireless settings. To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

First login your accountClick Maintenance at the top of the screen.Now enter (and repeat) your desired new password. Click Save Settings to update the router password.

You need to reset your router.

I believe that you can do this by pressing and holding the reset button (You may need a paperclip to do this) for 30 seconds. the power LED will start to blink, and then it will reboot with the defaults. You should be able to connect to it with 192.168.1.1. The default password is likely "password".

Download Wireless Key View at: http://www.nirsoft.net/utils/wireless_key.html

Use the web admin interface. Under wireless the user is SSID and the password known as the key.