Samsung DMT400RHW Builtin Dishwasher - Answered Questions & Fixed issues

I had the same problem, SAMSUNG did not want to tell me how to fix so I jumped in with research I found that after you remove the power supply, i.e. plug, 1) you need to remove the dishwasher and turn it upside down. 2) There is a white sensor tray; 12x12 approx. on the bottom held in with two screws, remove the screws and use a flat head screwdrider to undo the clips holding the tray in place. 3) Dry the tray and sensor tips with a towel and replace the tray. Bammmm, you have just fixed the LE(leaking error) code error.

Did you get a solution for this problem because my dishwasher is doing the same thing.

It is probably in timer mode. Consult your user manual.

First things to try: 1. Unplug the fridge and move it away from the wall. 2. Inspect the power cord for damage. Replace the power cord if it is damaged. 3. Plug the fridge back into the wall outlet. 4. Set the temperature control to the desired level. 5. Push the "Reset" button, located near the temperature control panel, to reset the temp control settings. The Reset button is usually red in color. 6. Move the fridge back to its original position.

Incoming water temp or pressure is too high

Question edited for clarity. Question moved to maker category. Try these.

How to reset your Samsung dishwasher

Samsung https://www.samsung.com > answer > ANS00087943 Hold Smart Control until AP displays (about 3 seconds). · Hold Hi-Temp Wash until the dishwasher chimes (about 7 seconds). · Turn off the dishwasher.

Samsung Dishwasher won't start

Repair Clinic https://www.repairclinic.com > RepairHelp > Samsung... The thermal fuse shuts off power to the dishwasher if it overheats. If the thermal fuse blows, it will prevent the dishwasher from starting. More plus videos. https://www.google.com/search?q=Samsung+DW80j3020US+Dishwasher.+It+has+no+power+to+the+power+button ..

hello inspect the float switch it might prevent the dishwasher from filling with water if its malfunctioning or stuck

Try home depot they sell parts you can order them in the store .

a manual reset if the 'Delay Start' feature has been activated.. by turning off power by unpluging it or off at the breaker for 30 seconds.

If your dishwasher is stuck in the drain cycle and the lights are flashing, it may be due to a faulty drain pump. You should check the drain pump and hose for any blockages or clogs. If these parts are clear, then the next step is to check the wiring between the dishwasher and the drain pump. If there is a loose wire or a broken connection, then this could be causing the issue. If the wiring seems fine, then the issue may be with the control board or the drain pump itself. If this is the case, then you will need to replace either of these parts to get your dishwasher back to working order.

It sounds like there may be an obstruction in the glide track that is preventing the third track from moving freely. Here are some steps you can take to try and resolve the issue:

1. Check for obstructions: Take a close look at the glide track where the third track is getting stuck. Look for any debris or objects that may be blocking the track. You can use a flashlight to help you see better. If you find any obstructions, carefully remove them.
2. Clean the glide track: Even if you don't see any obstructions, the glide track may be dirty or have accumulated debris. Clean the glide track with a soft cloth and a non-abrasive cleaner to remove any buildup that may be causing the third track to get stuck.
3. Lubricate the glide track: If the glide track is clean and free of obstructions, it may need to be lubricated to help the tracks move more smoothly. Use a silicone-based lubricant, such as WD-40 Silicone Lubricant, to lubricate the glide track. Apply a small amount of lubricant to the track and use a soft cloth to spread it evenly.
4. Check the glider tracks: If the above steps do not resolve the issue, the glider tracks may be damaged or misaligned. Check the glider tracks to see if they are bent or damaged in any way. If so, they may need to be replaced. If the glider tracks are misaligned, adjust them so that they are straight and parallel to each other.

If none of these steps resolve the issue, it may be worth consulting with a professional technician or contacting the manufacturer for further assistance

The clearance is governed by two things The height of the shelf and the height of the spray bar. Pull out the basket and check the screws holding the rails to the body. Remove the spay Bar and check the bushings and whatever dictates the height. It should spin, but shouldn't wobble.

Too much water in the machine. Normally air in the water level diaphragm switch tube. More on this at the bottom.

What is the meaning of the error codes displayed ... - Samsung

https://www.samsung.com > ... > Home Appliance Dec 7, 2021 - The OC, 0C, or oE error code appears when there is more water in the dishwasher than there should be. This is often very closely related to ...

• Samsung dishwasher is displaying an error code

  https://www.samsung.com > support > TSG01002074 An error on your dishwasher indicates a problem. Here's a reference list so you can identify what the problem is and what steps are needed. Videos and more information https://www.google.com/search?q=Samsung+model+DW80R5060US+0C+error ..

Hey Randy, thank you for the query. According to my research the E3 error code means that your dishwasher is unable to fill with water. To fix this problem, turn the water supply off and unplug your dishwasher from the power socket. You can then remove the water hose and check the water inlet valve to ensure it's working correctly.

Duplicate post deleted. Refresh the page to see your question posted. Try a reset https://www.samsung.com/us/support/answer/ANS00087943/ Videos as well https://www.google.com/search?q=unlock+Samsung+Dishwasher+DW60A8050FG ..

If the water valve is clogged or defective, water will not flow into the dishwasher. Water inlet valves are not repairable—if the valve is defective, you must replace it. Over time, calcium deposits can build up in the water supply valve or in the small filter screen inside the water inlet valve.

https://howtofixit.net/samsung-washer-code-sc-or-5c/#:~:text=The%20error%20code%20is%20actually%205C%2C%20though%20it,triggered%20by%20a%20problem%20with%20its%20draining%20function.

What does this nylon cord do? It isn't listed in the pages I looked at. There are parts diagrams and all the parts. https://www.google.com/search?q=samsung+dmt400rhs+parts ..

un power unit for a few minutes then turn back on should reset