20 Most Recent Aqua Signal Questions & Answers


I think there is a nut holding the prop to the shaft and there might be a shear pin going through the prop and shaft. Remove those to get the prop off. It may have been on so long, there might be rust and other junk holding it on. Spray with penetrating oil and let sit to loosen the rust.

Boating | Answered on Oct 31, 2019


I suggest you post your question on this forum:

http://www.boatered.com/forum/topic.asp?TOPIC_ID=131726

Boating | Answered on Oct 30, 2019


I suggest you go to this site and obtain a manual for your Evinrude engine. Hope it helps:

Literature

Boating | Answered on Oct 30, 2019


In demo mode, it will show fish and bottom details when the transponder is out of water. If the boat is in a mooring, put a metal spade under the transponder, you should see the detail change.

Google

make model manual

Boating | Answered on Oct 28, 2019


https://www.lowrance.com/en-au/help--support/fishreveal-software-upgrade/
It wont hurt to update any software,
Hope it works out,
cheers.

Boating | Answered on Oct 27, 2019


Sounds like one of the pins on the cable from your transducer is bent where it plugs into the back of the unit. check that first, then ensure the plug is all the way in. If it's not that, it's possible a wire is broken in the cable. You could try the wiggle test. With the unit on, have someone watch the screen and wiggle the wire that you can reach working from one end to the other. if the screen flashes or changes while you do this in a certain spot, there's your problem. This kind of problem usually comes from the wire being tight where it goes around a corner. Heat and vibration will finish the job

Boating | Answered on Oct 26, 2019


Try the following.
Ensure the connector going to the controller is secure.

Remove power to the motor by stowing it. Wait until the remote screen goes blank. Deploy the motor to power it up verifying that the System Ready light comes back on when the motor is deployed.
Press any button on the remote to turn it on.
If F code returns then probably controller board will need replaced.

Boating | Answered on Oct 26, 2019


Once a Honda has an oil spill ti seems like forever before they stop dripping. on the larger ones, we would remove the side cowlings and use a degreaser and wash them out.

Boating | Answered on Oct 26, 2019


Let it dry out. Then check it on dry land. You need to reseal the motor before putting it in the water.

Boating | Answered on Oct 26, 2019


If it just blowing the fuse at one speed or top speed it could be a short in the speed control or the negative cable is dirty. clean up the terminals and try again.

Boating | Answered on Oct 26, 2019


Hello, The owner manuals that come with the boats are so basic that you could use anybody's manual. if you need help in anything just ask.

Boating | Answered on Oct 26, 2019


It should be about 525 lbs dry weight.

Boating | Answered on Oct 22, 2019


If you are really interested, check to see if a library has this book : Chronometer Makers of the World by Tony Mercer. It should have info on the year of manufacturer.

Boating | Answered on Oct 20, 2019


and what is your question?

Boating | Answered on Oct 17, 2019

Not finding what you are looking for?
Aqua Signal Logo

0 questions posted

Ask a Question

Usually answered in minutes!

Top Aqua Boating Experts

ray gallant
ray gallant

Level 3 Expert

64733 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

29395 Answers

Tom Chichester

Level 3 Expert

54386 Answers

Are you an Aqua Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Aqua Boating

  • Aqua Boating

Most Popular Question

wire 2

  • Boating
Loading...