Bunn My Cafe MCP - Answered Questions & Fixed issues

yes sure isworking

Too much pressure makes the poor seal around the spray head leak. It happened to me, too. Call Bunn. They sent me a new one free of charge. Plus, you have to use purified water and clean it regularly to prevent buildup like calcium from causing similar issues (I use a gravity water purifier, but it doesn't remove natural minerals). I've had mine a year and that was the only problem. Much better than the multitude of Keurigs I had before. The awful difficulty opening the drawer will subside with use. And, they stand behind the machine in full for the 2 year warranty, meaning they'll replace the whole thing free if something happens

Add about a half cup of white vinegar to the water an run it through the maker about three times.After that use fresh water about three times. should be cleaned out .

It has a bad diode

It's threaded. Just unscrew it.

This model of brewer doesn't allow for changes in the calibration. If you've been using it for a while and notice a change in volume chances are the brewer needs to be cleaned. Here is a link to the full manual. http://www.bunn.com/pdfs/manuals/41980.0000.pdf

It sounds like the thermostat or Element is failing and causing your unit to overheat and boil. Probably time to call Bunn and see if your unit is under warrenty.

Somewhere inside you should find a small rotary thermostat. Also make sure the heating element is completely clean by using a quality descaler like CLR. A lot of people use white vinegar but it is not that effective on coffee makers. Make sure the heating element under the carafe is working, because that is heating up as the coffee is brewing. ..

Question edited for clarity and toss in a load of CAPS. It is dated with a non intuitive, none readable code. You can see examples here. Where is my Date Code? BACK OF BREWER Sticker on the lower back of brewer BOTTOM OF BREWER Sticker attached to the bottom baseplate of your brewer. Note: Allow water in tank to cool. Drain water before turning over.

Where is my Date Code? - BUNN

More here https://www.google.com/search?q=Bunn-o-Matic+HB+coffee+maker+read+the+date+code ..

unplug machine and turn upside down and pour out coffee and water mix (if water was in reservoir) If necessary turn over and fill will water and repeat.

Replace and run a pot of clean water thru it.

To locate the date code on your BUNN BT Velocity brewer, you can try the following:

1. Check the bottom or back of the brewer: Look for a label or sticker on the bottom or back of the machine. The date code is typically printed on this label.
2. Inspect the sides or inside the brewer: In some cases, the date code may be located on the sides or inside the brewer. You may need to remove any panels or covers to access the label or sticker.
3. Consult the user manual: If you have the user manual for your BUNN BT Velocity brewer, it may provide information on where to find the date code. Refer to the manual for specific instructions or contact BUNN customer support for assistance.

If you are still unable to locate the date code on your brewer, I recommend reaching out to BUNN customer support directly. They will be able to provide you with accurate information and guide you in finding the date code on your specific model of the BT Velocity brewer.

Normally that would be an easy fix if the water just continued to flow. You just replace the water inlet valve and they can stick open or partially open. But you say if you power off, the flow stops. That sounds like the control board is supplying residual power to it. Control boards are expensive so I would call for service. Or you can try some of the fixes here. https://www.google.com/search?q=bunn+coffee+maker+cwtf15+replacement+water+inlet+valve More here https://www.google.com/search?q=bunn+coffee+maker+cwtf15+water+not+shutting+off ..

shorted water heater element

Question edited for clarity. Question moved from Cars and Trucks. Probably needs a new water inlet valve. Google Bunn model water inlet valve

Bunn Valves, Solenoids & Fittings ' Parts Town

https://www.partstown.com > bunn > parts 266 items - How to find your Bunn model and serial number ... Bunn 27370.0007 Solenoid Valve Assy, Bypass-Plastic, 120V. Add to My Parts. In My Parts. https://www.google.com/search?q=Bunn+model+water+inlet+valve ..

Question edited for clarity. Question moved from Refrigerators. Hi again Bill Making a new post as a follow-up doesn't work here at Fixya. Posts are not threaded or linked, so this post has no context to your previous post. What you wrote here should be in the older post as a reply to Brett and I. You just click COMMENT under our answers to you. The benefits are that it keeps everything together and we get a notification that you require further help. And apparently is is a 'Bunn GRX-B Coffee Maker'. Capitalization and dashes are important to the search :>) https://www.fixya.com/support/t29863408-need_temp_limit_switch_garbage_bunn ..

Not sure your model name is correct and we always need numerical model names here. Bunn are such a well known name in coffee machines, I find it disappointing that they say ANY machine is not repairable. I found some Training Manuals and I found a 'Thermostat Limit Kit'. https://www.google.com/search?q=bunn+grab+fast+brew++temperature+limit+switch The search query would be Bunn (numerical model number) temperature limit switch ..

i think you may have to get a new one

only from BUNN AND POSSIBLYTHRU A DEALER

I have the identical problem, and I noticed it this morning after there were 2 very brief (seconds) power outages the previous night. Reading around the internet I read that the fuses inside the unit are the likely culprit, and need to be replaced. You can buy fuses made by others, for this unit. But not from Bunn. And there are video instructions around that show how to do it. The fuses are crimped on, not soldered. Mind you, I haven't tried to do this, yet, but that's what I read. Good luck!