Top 20 Brother DCPJ125 All-In-One Inkjet Printer Questions & Answers

Are the inks full? Have you tried the head cleaning utility in the printer drivers? If those don't work, get the inks out of the printer, soak the print heads in thinners and try the nozzle cleaning utility again. If that doesn't work i think you may need some new print heads/ink

Remove the power source of the printer Press the menu button .. Do not leave this button wait a bit Press 8 Okay Press 0 Okay wait a bit Use the buttons START (Mono + Color) until it reaches the purge Press this order figures 2 Okay 7 Okay 8 ok 3 ok Wait until the value turn into zeros Press exit Press 9 Then 9 The printer will restart End --------------- EZZAT FROM EGYPT 002 01277289325

unable to print 4F your printer is need to replace new printer head, this the best solution for your printer

Purge Counter Reset Instructions Please note that some of the terms used below to describe buttons may change from one printer to another. For example:

• START may be down as MENU or SET on your printer or be a green button
• STOP may be referred to as EXIT or a red button

Before you begin the reset procedure your Brother inkjet printer needs to be in maintenance mode, but depending upon the model of your printer the method of doing this will vary. For most modern Brother printers please try the following:

1. With the printer turned on and ready to print remove the power cable from the printer (or turn the printer off if you have a fixed power cable).
2. Hold down MENU/SET/START and re-insert the power cable/turn it back on.
3. Keep the button held down until the screen reads MAINTENANCE.

If your screen does not now say MAINTENANCE it will need to be put into maintenance mode using one of the two methods below:

• Printers with a built-in Fax: Hold down MENU/SET/START and quickly press * 2 8 6 4.
• Printers WITHOUT a Fax: Hold down Menu/Set and the Black Start key before pressing the UP arrow four times.

Now your printer should say MAINTENANCE on the screen and you are ready to begin the process of actually resetting the purge counter.

1. Type in 80 using the numerical keypad.
2. Use the DOWN key to locate the purge counter. eg. PURGE0060025
3. Use the number pad to enter 2783 (this should zero the numbers after PURGE).
4. Press STOP/EXIT to return to the first stage of maintenance mode.
5. Press 9 and 9 to exit maintenance mode.

Your purge counter is now reset and you can now resume printing as normal. If however this has not cleared the error message I advise going through this guide again following the instructions to the letter. If the error persists please let us know.

The ink absorber box or flushing box is nearly full. These components are periodic maintenance items that may require replacement after a period of time to ensure optimum performance from your Brother machine. Because these components are periodic maintenance items, the replacement is not covered under the warranty. The need to replace these items and the time period before replacement is dependent on the number of purges and flushes required to clean the ink system. These boxes acquire amounts of ink during the different purging and flushing operations. The number of times a machine purges and flushes for cleaning varies depending on different situations. For example, frequently powering the machine on and off will cause numerous cleaning cycles since the machine automatically cleans upon power up. The use of non-Brother ink may cause frequent cleanings because non-Brother ink could cause poor print quality which is resolved by cleaning. The more cleaning the machine requires the faster these boxes will fill up. http://support.brother.com/g/b/faqlist.aspx?c=as_ot&lang=en&prod=dcpj4110dw_eu_as&tabid=2

good day, unable to print 4f is printer head problem...replace new printer head

Paper jam, do a thorough inspection looking for any stuck bits of paper.

replace new printer head...thats the best solution

replace the printer head of your printer

Either the print head or the PH PCB is faulty.

Sorry... Print head damaged. There is an very low possibility to erase the error without buying new print head, but it's unprofitable

Print head or the PH PCB is faulty

Try one or more of these options:replace the carriage PCB ,replace the head/carriage unit,replace the main PCB.

your printer need to RESET step 1: Long press the menu button on your printer, then wait, if you see that the maintenance appears in the LCD release the menu button the type 80 then mono 25 times or above if you see the PURGE type this 2,7,8,3..then the PURGE is 0000 type 99.. then unplug

Sorry... Print head damaged

Hello, please go to this link and see video and get the start to troubleshoot step by step. http://www.refreshcartridges.co.uk/igloo/how-to-reset-purge-counter-on-a-brother-printer/ Your Problem is Solved. Enjoy the Printing :) Thanks And Regards, Piyush Gohil

Look in the user manual under errors or go to the Brothers support website and look up the model and error codes.Brother Printer Support

You need to reset counter or change absorber ?