20 Most Recent NetGear WGR614 Wireless Router - Page 5 Questions & Answers

the default username and password for netgear router is admin and passwordif in case you have change the username or password and you dont remember what it is just press the reset button at the back of the router for 5 sec, careful though cause this will also delete all the info that you have input in the router the first time such as isp info this will cause disconnection from the internet, but as soon as you know those info you can go ahaead and do this. this will also reset the username and pass of the wifi connection.

There would be a small hole behind the power button. It's a little bit small so dont think that it's not the right one.

1.Launch your Web browser and then type 192.168.1.1 in the address field. Click "Enter."

2.Click "Basic Settings." Input the configuration information given to you from your ISP in this screen. The settings not given by your ISP can likely be left at their default value. Click "Apply" before navigating away from this screen.

3.Click "Wireless Settings" in the menu on the left side of the screen. Enter or select the appropriate settings in the Wireless Settings dialog. Select the appropriate Security Options, then generate the security key. Click "Apply" before navigating away from the Wireless Settings dialog.

4.Reboot the router for the changes to take effect.

Good Luck, Jopica123

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

You need to use WPA2 and not WEP. WEP is no longer secure.

Hi John, Have you tried resetting the router using the internet address? When your IE stops with "Can't open Page" type into the URL box 192.168.100.1/gscan.htm. This should give you the router maintenance page which will tell you if it is working ok and options to try and reset it.

There should be a reset button located a the back of your router, while the router is plugged in press button with a pen and hold for 15 seconds. Lights on front of router should flash or something the that nature.

This router is only capable of using the 2.4 Ghz range. If you are experiencing interference on your wireless network you may want to try to change the wireless channel. If you have other devices in the location that uses the 2.4 Ghz range you may want to research to see if they also have the option to change to another channel as well.

1. Connect with your computer through one of the RJ45 jacks at the back.
2. Turn on you computer and connect to the router (factory default is http://192.168.0.1 unless it was changed)
3. Enter your user name and password (factory default is "admin" for the user name and "password" for the password.

If you changed any of the above and don't remember how it was set it up. You'll have to reset the router to factory defaults and reconfigure your router. There is a switch at the back of this router to do this (you need a paper clip to press it). If I remember correctly, you have to hold the switch and power the router. , you have to hold the switch and power the router.

When you set up your router you should also set up a password on it. Go back to your full manual and look for the security set up. It should give you directions on how to set it up.

This is a 14 year old router and runs at a very slow speed. It will not support video with todays high resolution cameras. Probably time to upgrade to a 802.11G router.

If the router has "N" value it should run a good distance away, even to the neighbors home. If "G" 30 Feet to 50 feet max. 40 Feet is difficult if passing through thick walls or steel buildings. If it is not an "N" router, then you need that or an Extender system. See TigerDirect for hardware replaements.

What model/manufacturer is the router?

you can use network genie or just as easy go to 192.168.1.1 and do it there. default username is admin password is password

reset to factory default press and hold reset button during the whole process and only release when completed. 1)press reset button 30 seconds 2)remove power cable 30 sec 3)plug in power cable 30 sec and then release. You should no be set for 192.168.1.1 username admin password is password

once there you need to type username admin and password is password if you cannot do it ,you may have to do: reset to factory default press and hold reset button during the whole process and only release when completed. 1)press reset button 30 seconds 2)remove power cable 30 sec 3)plug in power cable 30 sec and then release. You should no be set for 192.168.1.1 username admin password is password

user name if default is admin password is password

What is the problem ,tell me where you are having problems so I may help you set it up.

That is the setup page ,you need to log in user name is admin password is password.

No when it is blue it means you have internet,when it is yellow or amber there is no signal.Are you sure that your router in its settings that the wireless check box is enabled ? Can you connect with cable for certain.Probably you need to check the setting like I posted here.