Top 20 Daewoo KOR1NOA Microwave Oven Questions & Answers

One could unplug the power cord and take off the back metal panel.The turntable runs off a rubber belt.Be very careful as the capacitor holds one hell of a voltage. It is usually encased by a metal shield... but be very alert.Do not run the microwave with the cover off..

Hi,
Here is a tip that will help you to figure out what is wrong with yourMicrowave Oven....

Microwave Oven Basic Troubleshooting Tips

heatman101 ';
';
';

Take it to a Daewoo Service Centre, and they can get parts and you don't really want to be messing inside a Microwave.. In normal circumstances, with a cheap make like Daewoo, you just replace them, but get a quote. Help and videos in the link, if you choose to take the risk. https://www.google.com/search?q=Daewoo+KOC-925T+microwave%2Fconvection+touchscreen+will+not+work https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

read this! https://www.ifixit.com/Answers/View/285420/Daewoo+microwave+shines+but+does+not+heat Time for a new microwave.

take outer case off and find the light .

try putting 90 in the time that should be 1 1/2 hours

Check the rear for a screw cap fuse. If there isn't one, you need a Daewoo service centre.

The voltages inside a microwave oven are very dangerous, potentially fatal, so clearly the testing and repair need specialist experience and test equipment... Anyone needing to ask the question clearly should contact their local repair shop.

The key pad assembly is faulty as the carbon contacts get disconnected,the only remedy is the replacement of touch key pad.

Does it have a turn table that spins your food container? If so, does it turn? If not, you are getting a solid directed beam of microwaves focused on one part of your food leaving the rest of it ignored. If it doesn't have a turn table, it will have a wave spreader inside which is nothing more than an aluminum fan that is sometimes driven by a small motor and rubber belt. You won't see this as it is inside the chamber that contains the magnetron that generates the microwaves. These belts can break allowing a solid, focused microwave beam to shine on your food rather than be distributed around the oven, again, leaving the rest unwarmed. If this is the case, using the oven can damage it over time. If you don't know what you are doing, DO NOT try to repair it yourself!!! If you don't get the outer casing back together properly, you can expose yourself and / or your family to dangerous amounts of microwave radiation. You should take it to a qualified service center for repair but I would venture a guess that it is already damaged because of your statement "but getting increasingly unreliable". Even if it isn't damaged, it will probably cost you more in labor to fix it than it would cost to replace it. Good luck.

No definitely not normal. Call qualified service tech.

See my video here: https://www.youtube.com/watch?v=ITHDE-vFaiw

Hello Stephanie. Get a new filter and try again. Otherwise scrap the micro. It the filter plate rusted through, or is it burnt? The microwave's Magnetron-wave-guide is just behind this filter plate. Looks like a small tube with a silvery cap with hole in center. Very hazardous condition here. The high energy from it is damped by the filter. Is there food in the micro when arcing happens? An empty micro will arc.

Could be anything froma bad Magnetron to a bad door switch or loose connection at mag or HV capacitor.Could be a bad solder connection to the power relay on the main circuit board/ timer. Is it making any loud humming sounds? If so, that would be either a mag shorted to ground or a shorted rectifier. A shorted Capacitor would cause it to blow the fuse. A pretty broad question, its not heating whats the problem!!!

I have painted many Microwave oven cavities. You have to sand down the pealed off rusted areas and completely clean and degrease. Before painting, I use laquer thinner as a cleaner degreaser. Fumes can be a bit strong but it has worked well of me. I normally buy an automotive spray paint. They have a lot of different colors and a lot of the import colors can really come close to the color inside the microwave. Spray on thin layers till you get good coverage and make sure you let it dry thoroughly before trying to use. The paint in a Microwave isi not a special microwave energy protective paint. it is only there to make it look pretty and protect the metal. So a good automotive paint normally works fine.

Daewoo KOR 6QDB Operating Instructions Cook Book Controls Setting The...

get a tape measure and measure thea external dimension of the dead microwave go to a retailer and measure the dimensions of new microwave ovens and one with the same or slightly smaller dimension will fit in the power or wattage of the unit is of little consequence but don't get smaller than what you had but a a bit bigger will be good