20 Most Recent TP-LINK TD-W8901G Router - Page 4 Questions & Answers


Hi,
I have to assume you are referring to TP-Link power line adapters. In any event, pick the one that is not working. Press and hold the Pair button for a second or so, the Power LED will start flashing. Wait 2 minutes, then press and hold the Pair button of your main (other) TP-Link for 1 second, the Power LED will start flashing. In about 2 minutes all should be good.
If not you may have to reload the flash software or use the disks to reset.
Cheers

TP-LINK... | Answered on Jul 13, 2017


If you don't have access to the settings the handset is using to select the security protocol, or know what they are, the issue is probably with the protocol the handset is using to connect to the wifi, Check the computer that can connect, to see which protocol it's using. Then, I'd try a support ticket with the manufacturer of the handset to see if the issue is resolvable. It really depends on how flexible the handset protocols are...None, WEP, WPA2-PSK (TKIP), WPA2-PSK (AES), and WPA2-PSK (TKIP/AES) are all different options. Choose the wrong protocol, and you can't connect.

TP-LINK... | Answered on Jul 03, 2017


Google has many different ip addresses. They have servers I guess you call them everywhere. I downloaded several apps that looked up IP addresses cause the ping had different ones I didn't use. They all led back to GooGle owning that address. Nothing to be alarmed about, theres just no escape from Google, they see everything, track everywhere, and won a lot of different IP

TP-LINK... | Answered on Apr 07, 2017


this document should explain what to do
http://www.tp-link.com.au/resources/document/VPN_Config_Guide.pdf

TP-LINK... | Answered on Mar 29, 2017


If all devices say they are connected then check the Internet light on the router to make sure it's lit. It usually looks like a little globe. They may be connected to the router but the wireless is not connected to the Internet. Try unplugging the router for 30 seconds anf then plugging it back in. If that doesn't work call your service provider.

TP-LINK... | Answered on Jan 03, 2017


Reset it with the pin hole on the back or the bottom. Everything will change to factory defaults.

TP-LINK... | Answered on Sep 10, 2016


All you should need to do it plug in the Ethernet cable from your modem. Wait for your router to get an ip address then look at the available connections on your computer and click connect.

TP-LINK... | Answered on Aug 08, 2016

Tip

Recovering a dead TP-LInk Router


My router Archer C7, stop working suddenly. No flashing LEDs, cannot connect to it. Use the serial connection to the UART, and found it stops at the boot up stage, cannot find the apps to run......

Found the flash on the board, and put pressure on the flash IC. The unit comes up again and working.......

Put some flux on the flash pins, and run a hot solder across the pins. All working now.

My problem is dry joint of the flash. Others may have corrupted software and the serial connection will be a great help.

on May 29, 2016 | Computers & Internet


You will have to do the initial set up. There should be a disc that came with the router that will guide you through step by step. If you do not have a disk then you will have to get on the internet somewhere else and load the software from the manufactures site.

TP-LINK... | Answered on Apr 18, 2016

Not finding what you are looking for?
TP-LINK TD-W8901G Router Logo

62 questions posted

Ask a Question

Usually answered in minutes!

Top TP-LINK Computers & Internet Experts

Zaid Anarwala
Zaid Anarwala

Level 3 Expert

457 Answers

alex metro
alex metro

Level 3 Expert

364 Answers

 Mike M
Mike M

Level 3 Expert

3324 Answers

Are you a TP-LINK Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

TP-LINK Computers & Internet

  • TP-LINK Computers & Internet

Most Popular Question

update whole firmeware tplink w8901g

  • Computers & Internet
Loading...