20 Most Recent Kenwood KDC-MP4028 CD Player - Page 6 Questions & Answers

5227

You must have the yellow and the red wires tied together on a constant voltage source.

Only the yellow wire should be on a constant voltage source.

The red wire should only get voltage when the ignition is turned on or in the acc. position.

You need to rewire the red wire on the radio.

Let me know if it helps.

call kenwood you need the model and serial number and they may charge $25...

Sounds like you have
1) the rear speaker cable is plugged into the wrong colored hole
2) the audio software thinks you have a subwoofer, but you don't? Check on the audio software for ways to configure the speakers, the latest chips auto-detect when you plug in a cable, and ask you what that was you plugged in.

IT WAS JUST TO DAM COLD OUTSIDE. AFTER THE CAR WARMED UP INSIDE IT STARTED WORKING

Here is a manual on how to set the time page 22.

http://inform3.kenwoodusa.com/manuals/KDC3011.pdf

Good Luck

Please Rate FixYa!

Congratulations, is there anything we can help with?

If it brand new take it back to were it ws purchased to have it replaced.

according to kenwood code e-05 means the cd is upside down. www.kenwoodusa.com

there should be a reset switch behind the face or really small on the face .....email me

try to reset the radio it should be behind the face

it sounds like your wires need to be reran you might have a bad wire or two if that doesnt work email me

MAKE SURE U HAVE ALL OF THE COLORS MATCHED UP ON THE WIRES

TRY TO ORDER THE MANUAL IF U DONT ALREADY HAVE IT AND LOOK IT UP OR U CAN TRY THIS: FIND THE RESET BUTTON AND RESET IT. U MIGHT HAVE A CODE ON IT OR IT MIGHT BE SET ON DEMO

your radio has 2 blue wires. one of them provides a 12 volt turn on for a power antenna (when a cd is inserted that 12 volt turn on turns off, because when a cd is playing, the antenna doesn't need to be raised up). The other blue wire has a 12 volt turn whenever the radio or the cd is turned on--this is the blue wire that you need to connect to your amp remote line. ( pull out the radio and switch the blue wires)
respectfully,
Merle

http://www.kenwoodusa.com/Support/Car_Entertainment_Owners_Manuals/#_ This link should get you to the right place if not let me know and I can let you know how to get there. Good luck
-Andrew Hawkins

do you have a amp connected

check your yellow wire must be connected to the earth

You need the remote control to clear the code, if you don't have one, then you may need to go to a KENWOOD agent, or purchase one for your use.

KENWOOD SECURITY CODE CLEAR procedure Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!
Please rate ne FixYa for this solution. Good Luck :)