Top 20 Philips HSB2313 Theater System Questions & Answers

The shutdown seems to be caused by overheating of the heatsink electronics. My unit has a fan on the heatsink. This fan started making a noise. When I remove it the system shuts down as described. I will try to replace the fan.

The system must run through its routine before it can start up. If a mechanism is jammed or a switch is not contacting, it won't complete its routine and therefore will not start up.

Question edited for clarity. It you have standby, that shows you have power. The only things you can try is a Power Reset, disconnect from the mains, for 10 minutes. Press and hold the power button for 60 seconds and then plug back in. If you are using a remote, check the batteries in the remote. You can also do the check to make sure the remote is putting out a signal. Aim the remote at the front facing selfie of a smartphone. You should see a flash. No one else has reported your issue. https://www.google.com/search?q=Philips+fr-968+radio+receiver+no+sound+or+display ..

There doesn't seem to be one for this chinesium speaker.Probably a throw away item and not serviceable.

The Philips iPod dock model "AJ300D/05" is not responding when plugged in. To troubleshoot:

1. Check the power source and ensure proper connection.
2. If applicable, look for any blown fuses as a potential issue.
3. Verify the dock connector for a secure connection with the device.
4. Confirm device compatibility and consider using adapters if needed.
5. Check the remote control and its batteries.
6. Look for a reset function if available.
7. Update any associated software.
8. Inspect for physical damage.

If none of these steps resolve the issue, reach out to Philips customer support or a professional technician for further assistance or potential repair.

It could be due to a blown fuse and the fuse that has blown needs to be replaced.Or it could of had stopped working.

If your Philips CDR820 is not copying a disc when you press the "copy cd" button and then the "yes" button, there could be several reasons why this is happening. Here are some possible solutions you can try:

1. Check the disc: Make sure the disc you are trying to copy is not scratched, dirty, or damaged. If it is, try using a different disc.
2. Check the blank disc: Make sure the blank disc you are using is compatible with your Philips CDR820. Check the user manual for compatible disc formats.
3. Clean the laser lens: If the laser lens is dirty, it may not be able to read the disc properly. Use a cleaning disc to clean the lens.
4. Update the firmware: Check if there is an available firmware update for your Philips CDR820. If there is, download and install it to see if it fixes the issue.
5. Reset the device: Try resetting the device by unplugging it from the power source for a few minutes, then plugging it back in and trying to copy a disc again.

If none of these solutions work, it may be a hardware issue that requires professional repair. In that case, you may need to contact Philips customer support or a qualified technician for assistance.

Contact Philips direct. They probably have drivers and a Firmware / Software Bin File. https://www.p4c.philips.com/cgi-bin/dcbint/cpindex.pl?slg=en&scy=gr&ctn=SA1942/02 ..

possible bad drive motor

TRY USING A CLEANING DISK , IF IT DOESN'T HELP THEN A LOCAL REPAIR SHOP

Yes it can. contact Philips Support for their local service centre. https://www.philips.com.ph/c-p/LX3600D_69/- ..

If your new tapes squeak while recording, there could be misalignment in the record path or it could be worn. Curious that no tapes were supplied with the machine. Perhaps you can take the machine to the vendor to demonstrate operation with squeaking.

Replace the loading belt and check the timing.

many older units will not work for digital signals

This music system is a basic setup so your choices are limited. You could try using a cable connection. The type you need is a "phono jack plug" to "3.5mm jack plug" cable. They are usually very cheap and most TV and Technology Stores will keep them in stock. The cable has different styles of connector at each end. One end is the same as the round red and white plugs at the top of the photograph and the other end is a standard headphones connector. Plug the red and white pair into an 'Audio In' position on the back of the system and the other end into the headphone hole on your mobile phone. (Try the position above the two already in the system). Select the channel on the system for that connector and press play on your mobile device.>

T3.15A 250V https://www.manualslib.com/manual/1367013/Philips-Hts3000-98.html?page=1#manual https://www.manualslib.com/manual/1367013/Philips-Hts3000-98.html?page=25&term=F901&selected=3#manual

There is a manual here. https://www.manualslib.com/manual/549505/Philips-Lfh0388-Pocket-Memo-388-Minicassette-Dictaphone.html This may answer your question.. Regards Geoff

For connecting a soundbar to the TV, you have several ways. If you don't want to use the HDMI option, you need to go high-tech with a wireless connection. Another way is to use Aux or RCA cables.

Hi Darshan Ganesh, you can connect your phone to your Philips D573 You must connect the audio audio output of your phone (headphone output) to the Philips Auxiliary input on the rear panel Hola Darshan Ganesh, puedes conectar tu telefono a tu philips D573 Debes conectar la salida de audio de audio de tu telefono(salida de auriculares) a la entrada Auxiliar del Philips en el panel trasero https://www.philips.ae/c-p/FWD573_98/-