20 Most Recent
Panasonic PT-50LC13 50" Rear Projection HDTV - Page 9 Questions & Answers
How do i reeet the hour meter
Here is a link to replacing the lamp and the instructions for resetting the timer.
Just search for your set on the page.
I hope that this helps you.
asnowman
http://911phone.net/Panasonic_TY-LA1000_Instruction_Manual%5B2%5D.pdf
6/21/2010 11:13:47 PM •
Panasonic...
•
Answered
on Jun 21, 2010
Red lamp
If it is a new bulb and does not come right on you need to take the platis housing off of the old bulb and put the new bulb in the old housing, the new bulbs dont always fit just right
6/8/2010 9:33:09 PM •
Panasonic...
•
Answered
on Jun 08, 2010
I need to replace the lamp in my Panasonic
Hi,
Below image shows original TY-LA1000 lamp that comes in its housing.
Image-1
And this image shows bulb of TY-LA1000 lamp that many sites/ stores offer on less price.
Image-2
Let me know did you received lamp or bulb as replacement to help you out accordingly.
Thanks.
5/31/2010 8:45:51 PM •
Panasonic...
•
Answered
on May 31, 2010
My PT-50LC13 TV turns on
Hi,
Below three images shows how to get access to lamp cover and lamp inside
in Panasonic PT-50LC13 dlp tv.
1- Remove lower front cover.
2- You will see Lamp Cover there.
Tight screws as shown in above image.
Hope this will help you.
Thanks.
5/27/2010 12:11:35 AM •
Panasonic...
•
Answered
on May 27, 2010
How do you replace the lamp
If you don't have the manual handy you can download it here.
http://service.us.panasonic.com/OPERMANPDF/PT50LC13.PDF
But I did not find it much helps as all you need is a TY-LA1000 lamp that can be purchased from a number of dealers on the internet, or you may have a shop
locally that will sell you one.
I have even found them as cheap as $124.00 on Amazon.com.
The replacment instructions will come with the new lamp and also how to reset the lamp timer.
But here is a link to the lamp instructions.
http://www.fixyourdlp.com/wp-content/uploads/2007/09/panasonic-tyla1000-lamp-instructions.pdf
I hope this information allows you to resolve this issue.
I am doing this for free.
If I have helped you, please help me, and rate this suggestion.
If you need further assistance please comment to this post and I will try to help you further.
Thanks for using FixYa
asnowman
5/7/2010 5:27:15 PM •
Panasonic...
•
Answered
on May 07, 2010
Need to reset the lamp timer
1 turn tv on
2 press vol- on tv and pip on remote at the same time for more than 5 sec a message will appear
5/6/2010 11:48:59 PM •
Panasonic...
•
Answered
on May 06, 2010
How to reset lamp hours?
you can simply go to the tv sets menu and go to lamp hours and highlight it then highlight reset and press enter
5/4/2010 10:07:27 PM •
Panasonic...
•
Answered
on May 04, 2010
My 50 inch panasonic lcd projection keeps going to
check to insure that your input signal is clean,(clean picture) most modern TV`s blank the video if it is deemed of poor quality, also if you are using a VCR and are viewing pirate copy tapes the VCR will output a varying video level output signal to deter pirating of movies, using a video stabilizer between your VCR and your video input may solve this problem for you, check with your user manual as to the light flashing condition in the diagnostic section this will indicate the fault you are experiencing good luck
4/27/2010 9:17:06 PM •
Panasonic...
•
Answered
on Apr 27, 2010
Resetting lamp life after changing lamp
Hold VOL - on the TV
then aim the remote at the TV (watch so that your arm doesn't block the
remote signal and press PIP or the SPLIT button. Do this together for
at least 5 second. I hope this helps, best wishes.
4/27/2010 12:12:30 AM •
Panasonic...
•
Answered
on Apr 27, 2010
My tv just told me to clean the air filer, what
It means just that. Clean your air filter but to get to it is a different story. I would highly recommend calling an authorized service center to do it.. While he's at it, inquire about getting a ballast kit installed.
4/24/2010 3:13:49 AM •
Panasonic...
•
Answered
on Apr 24, 2010
Not finding what you are looking for?