Sony FD Trinitron KD-34XBR960 34" TV - Page 5 - Answered Questions & Fixed issues

If your Sony SLV-X715 VCR is not reading the cassette and you are receiving the error code 3L 22 AA, there could be a few potential issues causing the problem. Here are some steps you can try to troubleshoot the issue:

1. Clean the Video Heads: The error code you are seeing may be related to dirty or clogged video heads. Try using a cleaning cassette to clean the heads and see if this resolves the issue.
2. Check the Cassette Compatibility: Ensure that the cassette tapes you are trying to use are compatible with your VCR. Some tapes may not be compatible due to their format or quality. Check the user manual to ensure that you are using the correct cassette tapes.
3. Check the Cassette Loading Mechanism: Ensure that the cassette is properly inserted into the VCR and that the loading mechanism is functioning correctly. Check for any obstructions or damage to the mechanism that may be preventing the cassette from loading properly.
4. Reset the VCR: Try resetting the VCR by unplugging it from the power source for a few minutes, then plugging it back in and trying again.
5. Contact Technical Support: If none of the above steps work, you may need to contact Sony technical support for assistance. They can provide you with more specific troubleshooting steps or guide you through the process of repairing or replacing your VCR if needed.

It's worth noting that the error code you are seeing may indicate a specific issue with your VCR, so you may want to consult the user manual or online forums for more information on what the code means and how to address it.

Try replacing the tcon board, if that doesn't fix it chances are the panel is bad

Try this.....

Power off your device.

Unplug the power cord from the electrical outlet. Leave the power cord disconnected for at least a couple of minutes.

Yes, it's possible that the T-Con board in your Sony LCD TV may need to be repaired or replaced if it's causing vertical and horizontal white lines on the screen. The T-Con board is responsible for translating the digital signal from the TV's main board into a format that the LCD panel can display. Before replacing the T-Con board, you may want to try some additional troubleshooting steps, such as checking all the cables and connections, performing a factory reset of the TV, and updating the firmware. However, if none of these steps resolve the issue, then the T-Con board may need to be replaced. You can purchase a replacement T-Con board online or from a TV repair shop. If you're comfortable with electronics repair, you may be able to replace the board yourself by following instructions provided with the new T-Con board. Alternatively, you can hire a professional TV repair technician to replace the board for you.

The programming code for the Sony BDP S500 to be used with the RM-AAP013 remote is 31758. Here are the steps to program the remote:

1. Turn on your Sony BDP S500 player.
2. Press and hold the "S" button on the RM-AAP013 remote until the "Amp" button flashes.
3. Enter the programming code 31758 using the number keys on the remote.
4. Press the "Enter" button.
5. Wait for the "Amp" button to stop flashing.
6. Test the remote to ensure that it is working properly with the Sony BDP S500 player.

There could be several reasons why your Sony VHS player is starting and then immediately stopping with a scrambled picture. Here are a few things you can try:

1. Check the VHS tape: It's possible that the VHS tape itself is damaged or dirty, causing the player to stop and the picture to become scrambled. Try cleaning the tape or using a different one to see if that solves the issue.
2. Clean the player: Over time, dust and dirt can accumulate inside the VHS player, which can cause it to malfunction. Try cleaning the player with a soft cloth and compressed air to remove any debris that may be causing the issue.
3. Check the connections: Make sure that all the cables are properly connected to the player and the TV. Sometimes loose or faulty connections can cause the player to stop working or display a scrambled picture.
4. Check the settings: Make sure that the player is set to the correct mode (VHS playback, for example) and that the tracking is set correctly. Adjusting the tracking can help to improve the picture quality and prevent it from becoming scrambled.

If none of these steps work, it's possible that the player may need to be repaired or replaced.

The 6-time blink code for the Sony KE-42TS2U indicates a backlight error. This may be due to a faulty backlight inverter board, or a problem with the power supply to the backlight inverter board. It is recommended to have the TV serviced by a qualified technician to diagnose and repair the issue.

Programming a Coolsat remote to a Sony TV is a straightforward process that can be done in a few steps. Here's how you can do it:

1. Turn on the Sony TV: Make sure that the Sony TV is turned on and in the correct input mode so you can see the on-screen menu.
2. Locate the code list: Check the manual that came with the Coolsat remote for a list of codes for Sony TVs. The codes are usually organized by brand.
3. Try the first code: Using the Coolsat remote, press and hold the "Code Search" button until the light on the remote turns on. Then, enter the first code for Sony TVs into the remote. You can usually do this by pressing the number buttons on the remote.
4. Test the code: After entering the code, press the "Power" button on the remote. If the Sony TV turns off, then the code is correct and you can proceed to the next step. If the TV doesn't turn off, try the next code from the list. Repeat this process until you find a code that works for your TV.
5. Store the code: If you've found a code that works for your TV, press and hold the "Code Search" button again until the light on the remote turns off. This will store the code in the remote's memory and allow you to use it to control your TV in the future.
6. Test the remote: Finally, test the remote by using it to control the TV's volume, channel, and other functions to make sure everything is working correctly.

If the codes listed in the manual don't work for your TV, you may be able to find additional codes online or by contacting the manufacturer. You can also try using the "Code Search" function on the remote, which will allow you to find a code by scanning through all the codes in the remote's memory.

Updating the firmware on your Sony XR-77A80J can be a tricky process if not done correctly. To begin, you should check that the firmware update file on your 4GB FAT32 flash drive matches the version of your TV. You should also check that the 5 files inside the sony_dtv[...].zip archive have been extracted and loaded onto the drive correctly. Once you have done this, follow the instructions provided by TVPartsToday carefully. Make sure to plug in the drive before powering on the TV and not press any power button. If you are not seeing any kind of status light or display on the TV, you should check that the USB drive is properly connected. Make sure the connection is snug and the drive is fully inserted into the port. If the issue persists, you may need to contact a professional for help. They will be able to provide more accurate advice for your particular TV model. You may also want to refer to your owner's manual for further troubleshooting tips.

You could try testing the power supply by using a multimeter to look for voltage and see if any of the components are bad. If you can't find a schematic of the power supply, you may want to consider visiting a local electronics store or repair shop to get more help. Additionally, you could try replacing the fuse to see if that helps, but it would be best to confirm that is the issue before replacing it

If your Sony VPL-CS5 Red LCD isn't working, you may need to replace the lamp. You can purchase a replacement lamp from the manufacturer's website or from an authorized retailer. You may also need to check the power cord and connections to ensure that everything is properly connected. If the issue persists, you may need to contact Sony customer service for further assistance.

If you're trying to control your Philips 65PFL4864 TV with the remote control of your Sony BDP-S370 Blu-ray player (model RMT-B107A), you will need to find the remote control code that corresponds to your TV. The codes for different brands and models of TVs can vary depending on the remote control, but you can try using one of the following codes:

• Code 020
• Code 021
• Code 022
• Code 023
• Code 024
• Code 025
• Code 026
• Code 027

To use the codes, you need to follow these steps:

1. Turn on your TV and Blu-ray player
2. Press and hold the "TV" button on the remote control of your Blu-ray player.
3. While holding the "TV" button, enter one of the codes listed above.
4. Release the "TV" button and check if the TV responds to the commands from the remote control.
5. If the TV does not respond, try the next code in the list.

You should be able to find the instructions on how to program your remote control in the manual of your Blu-ray player. If you don't have the manual, you can download it from the Sony website or contact the manufacturer for assistance. Keep in mind that these codes are not guaranteed to work, and it's possible that your remote control may not be able to control your TV. In this case, you may need to consider purchasing a universal remote control that is compatible with your TV and Blu-ray player.

perform a soft reset. Turn off the TV, unplug the connector from the socket, and wait 2 minutes. ...

kindly check the power board if all voltages are there

1. Power button: Locate the power button on the front or side of the DVD player. Press and hold the button for a few seconds until the device turns on.
2. Power outlet: Unplug the DVD player from the power outlet and then plug it back in. This should turn the device on.
3. Power strip: If the DVD player is plugged into a power strip, turn off the power strip and then turn it back on. This should turn the device on.
4. Manual: Consult the manual of your DVD player if you have one, it may have a way to get the device out of standby mode.
5. Using the buttons of the DVD player: Some DVD players have a button on the front or back of the device that can be used to turn it on and off. If the device has a button, try pressing it to turn it on.

It's worth noting that these methods may vary depending on the specific model of your Sony DVP-C670D DVD player. If none of these methods work, you may need to purchase a replacement remote control or consult a professional for assistance.

Connecting your old RDR-HXD890 player/recorder to your Sky Q box and TV can be done by using the appropriate cables and connections. Here is an example of how you can connect the devices:

1. Connect the HDMI output of the Sky Q box to the HDMI input of the RDR-HXD890 using an HDMI cable. This will send the video and audio signals from the Sky Q box to the RDR-HXD890.
2. Connect the HDMI output of the RDR-HXD890 to the HDMI input of the TV using an HDMI cable. This will send the video and audio signals from the RDR-HXD890 to the TV.
3. Connect the aerial cable to the aerial input of the RDR-HXD890
4. Connect the RDR-HXD890 to the power outlet
5. Turn on all the devices and set the TV to the HDMI input where the RDR-HXD890 is connected.

By connecting your devices in this manner, you will be able to watch and record TV shows and movies from your Sky Q box through the RDR-HXD890 and display them on your TV.

To program a Sony TV, you will need to follow these steps:

1. Press the "Menu" button on your remote control.
2. Use the arrow buttons to navigate to the "Settings" menu, and then press the "Enter" button.
3. Navigate to the "Installation" or "Setup" menu, and then press the "Enter" button.
4. Select "Programming" or "Channel Setup," and then press the "Enter" button.
5. Follow the on-screen instructions to scan for available channels. This will typically involve selecting your cable or antenna source and then initiating the scan.
6. Once the scan is complete, use the arrow buttons to navigate through the list of channels and select the ones you wish to keep. Press the "Enter" button to lock them in.
7. Exit the menu when you are finished.

Note that the specific steps may vary depending on the model and software version of your Sony TV. You may refer to the manual of the TV to get more information.

To get a ST-PTZMINI-540W camera to work with a Nuvico DV3 1600 remote, you will need to follow these steps:

1. Connect the camera to the remote using a RS485 cable.
2. Configure the camera's communication settings to match the remote's settings. This can typically be done through the camera's on-board menu or through the use of a software configuration tool.
3. Once the camera is configured to match the remote, you will need to set the camera's address to match the remote's address.
4. Once the camera and remote are configured, you should be able to control the camera with the remote.

It is important to refer to the user manual of the camera and the remote as the steps may vary depending on the model and firmware version. If you are not comfortable working with electronics or you are not sure about what you are doing, it is always best to consult with the manufacturer or a professional technician.

Hi You can try. Part 1: Manual Factory Data Reset with TV buttons Press and hold the Power button and Volume Down (-) buttons on the TV (not the remote), and while holding the buttons, plug the power cord back in. Continue to hold the buttons down until a green LED light appears near the Sony logo on the TV front. ----------------- How do I factory reset my Sony Bravia TV manually?"); display: inline-block; height: 24px; width: 24px; margin-top: -1px; transform: rotateZ(-180deg);"> Factory data reset

1. Press the HOME button, then select [Settings] - [Device Preferences] - [Reset] - [Factory data reset].
2. Select [Erase everything]. If you have set a PIN code on your TV, you will be prompted to input it when you select [Erase everything].