20 Most Recent Sony FD Trinitron WEGA KV-32FS120 32" TV - Page 5 Questions & Answers

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/ Blinking codes details to many popular brand TVs are given. Surf the site with patience.

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Unlock procedure to many popular brand TVs are given.

Back-light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/

hi,
watch how many times ur standby indicator flashes. flashing of led is its self diagnosing system. if u tell me how many times its flashes, then i can tell u where is the problem
ok

Check and replace the main system control memory IC. It is faulty. If you wish to get some details; check the site linked here. Pull up older posts.Surf the site with patience.http://electronicshelponline.blogspot.com/

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. Viewing it in "Mosaic" or "Magazine" will make surf easy. http://electronicshelponline.blogspot.com/ Blinking codes details to many popular brand TVs are given. Surf the site with patience.

check the capacitor on power regulator area if there is puffed capacitor(bursted).blink means time delays but the power is not sufficient to stabilize because of a faulty capacitors and it triggers to stop the start kick.(some cases arehaving busted horizontal out transistors or shorted.

0286,0284,0280. Try these codes. If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common codes used for devices too are given, in the order of device brand name list in alphabetical order. Do a search by type in the brand name of your device, at its search box, and press "Enter". Or, pull up older posts. http://remotesearch.blogspot.com/ http://electrohelponline.blogspot.com/

From everything I've researched they are scammers. They are not accredited with the Better Business Bureau which is a sign for caution. Hope this helps. If you need further help, reach me via phone at https://www.6ya.com/expert/timothy_c6f309c0f75b6f43

Contact any service technician. Electro help

Check and replace damaged component/s at it video output section circuit. This circuit board can be located at the back of the picture tube; will be directly plugged on to it. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" or "Magazine" will make surf easy. Pull up older posts. Surf the site with patience. Do a search by type in the brand name of your device at its search box and press "Enter". http://electronicshelponline.blogspot.com/

Check all the solder terminals at its video output card, for any loose soldering. Re-solder all the suspected solder terminals, by applying a lit tile more solder to each terminals. This video output card can be located at the neck of the picture tube itself, will directly plugged on to the back of the CRT. Check all the solder terminals of CRT base connecting socket too. If you wish to get some details, check the site linked here. http://electronicshelponline.blogspot.com/Pull up older posts.

038,033,0335. Try these codes. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. See it in "Mosaic" or "Magazine" view. It will make surf easier. Or, do a search by type in the brand name of your device at its search box, and press "Enter". http://electrohelponline.blogspot.com/ Check this link too. http://remotesearch.blogspot.com/

Hi, Additional information is necessary to suggest a solution. For exemple, your screen is black or grainy when you select a channel. Please let us know to try helping you. Thanks, Sully

Bad board, call service man