Top 10 Sony KP-53HS30 53" Rear Projection HDTV-Ready Television Questions & Answers

how to lower the red screen voltage?

Indian pattern

http://www.justmanuals.com/sony-color-rear-video-projector-kp43ht2053hs2053hs3061hs2061hs30-chassis-parts-service-p-25567.html

Hi,
How to Enter Service Mode
1. Turn on the main power switch to place this set in standby
mode. (LED will light in red.)
2. Press the buttons on the commander as follows, and enter
service mode.

PRESS these buttons in sequence

ON SCREEN DISPLAY---> (DIGIT 5) ---> (VOLUME +) --->STANDBY

Method of Cancellation from Service Mode
1. Set the standby mode (Press “ (TV STANDBY)” button
on the commander), then press “ (TV STANDBY)” button
again, hereupon it becomes TV mode.


Thanks

Hi,
    Please check fisrst that indicator liight (LED) blinks how many times.it could be from 1 to 8 times and the interval would be of three seconds.So, count the led flashes how many times and then tell me i will try my best to find and fix the solution.

Thanks 

Its nice to save money but unless you know what you are doing and have the right soldering equipment its best to leave this to a pro. you can open your tv and inside there are two large ics labeled STK 392-xxx those are where the problem is , however with sony tvs there are fuses that need to be replaced and possibly some resistors,. have a tv shop repair your tv. Julio - Millenium TV in Las Vegas

These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. Convergence problems are very common on all Projection TV sets including Sony, Samsung,JVC,Philip Magnavox,Panasonic,Akai,Pioneer, Hitachi,Mitsubishi,Zenith and others.
You can get more information and a DIY convergenece repair kit with instructions from the link below.

Here are some of the most common problems with these sets...

Problem #1) Convergence

Yours may have one or more of the following symptoms...

*Screen Looks 3-D
*Colors wont align
*Screen may look distorted or warped
*No Audio/Video - TV Shuts down - May also make a constant chirping sound

Problem #2 - Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

*Dull looking picture
*White looking picture
*Halos around objects
*Red/Orange looking picture

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

The safe and easy way to do this is to first unplug the set and then remove the back cover.

Most likely you are seeing spider webs; with the back off I use a swiffer duster with a fairly long handle. Clean the three large black lens you will see with a lens cloth or a paper towel with glass cleaner sprayed on the towel.

With the duster get all the webs and do not apply force for any attached to the inside of the screen.

Common problem and I have seen it many times. It is a good idea to clean the lens on the three tubes once a year--any dust on them will make the picture look somewhat darker and dull.


SD TECH

You have a convergence malfunction.......the convergence ic's and the protecter picp fuses in the power are will need to be replaced by a qualified perso. A reputable shop may charge around $300 to repair. If you have technical ability,I can guide you further to repair yourself as well

tv will not turn on, red flashing light comes then turns off.
light flashes six times.