20 Most Recent Sylvania SRT2232S 32" TV - Page 4 Questions & Answers


Try website 1-800-remotes Factory original.Get the original remote.

Sylvania... | Answered on Dec 17, 2009


Hello SKrokau:

Have the IR sensor (Infared Sensor) replaced in this model. It is a common failue for Sylvania televisions. The IR sensor is the device used to receive commands from the remote and relay the commands to the microprocessor for processing. The sensor is very inexpensive and the total to repair should not cost you more then (FYI) $80.00 for parts and labor.

Have a Happy Holiday!

Sylvania... | Answered on Nov 23, 2009


Hello Skrokau:

Have the IR sensor in the television replaced. (Infared Sensor). It is common for these to fail in Sylvania televisions. The Ir sensor receives commands from the remote to be processed by the microprocessor. The sensor has gone bad.

This part is very inexpensive and should be quite cheap to repair.
FYI---This unit should not cost you more than a $100 bucks to repair including parts and labor...

Have a Happy Holiday!

Sylvania... | Answered on Nov 22, 2009


Unplug for several hours, press and hold power button for 5 seconds, wait half hour more, plug back in and try. Or press and hold either channel buttons at same time or volume buttons at the same time to see if that exits the mode.

Sylvania... | Answered on Nov 18, 2009


If you have a cable box connected, you have to set your tv in the menu for cable/satellite and not antenna.

Sylvania... | Answered on Nov 10, 2009


Is the picture stretched or shrinking and is it distorted or have lines? There are no vertical Height adjustment the circuit is prest and there is likely a problem in the vertical o/p circuit.
The problem is a bad Vertical Output IC (usually mounted on an aluminum heat sink with the part on it labeled LA78?? ) and 1 or 2 bad capacitors. Some times you can even fix the problem by re-soldering the contacts of the IC- To find the IC follow the 4 wires that come from the Yoke (which is a contained coil of wires slipped over the neck of the picture tube(s)) back to the board. 2 of the wires go to the horizontal o/p and 2 to the Vertical o/p the thinner gauge wires are for the vertical.

Sylvania... | Answered on Sep 28, 2009


You should get the vertical IC checked starting with checking the supply voltage on it. This is a small flat IC attached to a heat sink with about 9-11 pins. This tv model should carry an LA7837 or an equivalent IC. If supply is present, check with means of a magnifying glass for dry solder joints on it. Resolder the pins on this IC if necessary and should work out fine. Model tends to suffer from this problem.

Sylvania... | Answered on Aug 19, 2009


Hello kd6aaj, You are on the right track, a vertical line usually means that you lost horizontal deflection which is supplied by the horizontal/High voltage section.The thing that puzzles me is that you did not lose high voltage. Let me explain. In modern TVs the horizontal section uses scan rectification or a process similar to a switching power supply to convert a lower voltage tapped off of the hoizontal/HV section to provide B+ for the rest of the television. So if you lose your Horizontal voltage you lose your B+ also. So you will never see the vertical line because you low voltage power supply if off also. Now I think your Q571 (H-Out), Q572 (H-Drive), Q551 and/or Q552 (H-Control) might be good. However check them anyway. I would also advise you to check your yoke transformer for an open or shorted winding. This would cause you to lose deflection without losing high voltage. You are definatly in the right section just add the deflection section to your scope of troubleshooting.

Sylvania... | Answered on May 19, 2009


newer model televisions usually have a combination of buttons you can press on the front to reset them to the factory defaults. contact the most senior person that works in the electronics dept. where you bought the unit, they will usually give you some insight without much, if any hassle.

Sylvania... | Answered on Apr 08, 2009


that's because (at least on my GE universal remote) the TV should be set to 0189. try it.

Sylvania... | Answered on Apr 08, 2009


Thank you:
We found a universal remote at BestBuy.
caldwell

Sylvania... | Answered on Mar 23, 2009


Check the outlet to be sure you have power to it. Then check both ends of the tv power cord to insure that they are actually plugged in. good luck.

Sylvania... | Answered on Jan 23, 2009


ask staff at the company for a code or get a refund for your purchase

Sylvania... | Answered on Jan 23, 2009


you have fault oscillation you have defective parts inside. at the oscillation circuit.

Sylvania... | Answered on Dec 26, 2008


you can not play that game on ch3-4 you have an audio/video plug on thhe back of tv you have to change the tv tv the a/v settig or on some tvs the game setting

Sylvania... | Answered on Dec 03, 2008


Hello there. I'm sorry to say that it sounds as if the element that actually energizes your screen is bad. It is most likely overheating. or quite poosible the power converter lost a resistor or 2.

Sylvania... | Answered on Nov 28, 2008


your tv have a vertical trouble, maybe the ic is busted

Sylvania... | Answered on Oct 29, 2008

Not finding what you are looking for?
Sylvania SRT2232S 32" TV Logo

131 questions posted

Ask a Question

Usually answered in minutes!

Top Sylvania Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76204 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Caltronic TV Repair
Caltronic TV Repair

Level 1 Expert

12 Answers

Are you a Sylvania Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sylvania Televison & Video

  • Sylvania Televison & Video

Most Popular Question

codes sylvania tv

  • Televison & Video
Loading...