20 Most Recent
Uniden BC60XLT-1 Handheld Scanner - Page 5 Questions & Answers
Wanted to program frequencies into the scanner but
This is a new one on me. Press the review key to see if there is a frequency programmed on what could be channel 8 (P missing a segment of the display). Press the manual button then the period twice. If all else fails, open the case and push the reset button.
How do you program a
Detailed programming instructions are contained in the operating manual which you can download and print here:
http://www.uniden.com/pdf/BC60XLTom.pdf
Bill B
What is the year of
The operating manual has a copyright date of 1995, so manufacture would be that or a year or 2 later. My guess is '95 though, as that model did not have a long production run..
Bill B
How to program channels
Detailed programming instructions are contained in the scanner operating manual. You can download and print it, at no cost, here:
http://www.uniden.com/pdf/BC60XLT-1om.pdf
Bill B
HI my name is mark
Hi Mark: To deactivate the priority scan mode on the BC60XLT-1, just press the PRI (Priority) key while the scanner is running in either SCAN or MANUAL mode. If your scanner is something other than the BC60XLT-1, please provide your model number and I'll research the answer for you.
Bill B
I have a Uniden Bearcat
You can download and print your scanner's operating instructions, at no cost, here:
http://www.uniden.com/pdf/BC60XLT-1om.pdf
For a comprehensive database of active frequencies in your area, and a lot of other useful scanning information, visit:
www.RadioReference.com
Please give us a shout if you need further assistance with your scanner.
Bill B
I want to know how to get the police channel on my
There are several web sites that you can go to by using a search engine. Most of them want you to pay for free information. If you call your local police department, fire department and ask them for their frequency they will usually tell you. A good way is to ask a policeman or fireman in your community. I have used DXing.com, it is a free site. Hope this helped!
Have a bc2500xlt that battery pack is gone. were
The battery pack (BP2500) and power supply/charger (AD70U) for your scanner have both been discontinued by Uniden, but I did locate a battery pack on eBay. You can check it out here:
http://cgi.ebay.com/BP2500-Battery-Pack-Uniden-BC2500XLT-BC3000XLT-Scanner-/180531979744?cmd=ViewItem&pt=LH_DefaultDomain_0&hash=item2a088b65e0
Considering the fact that your scanner is about 15 years old, and the price of the battery pack is $56.99, you would probably be better off donating the scanner to a museum and buying a new one.
My apologies for being the bearer of bad news.
Bill B.
How can i program my scanner
To enter a known frequency (they're not codes) into your scanner:
- Power the unit ON
- Press the MANUAL key
- Enter a channel number (01 - 30)
- Press MANUAL
- Enter the frequency, including decimal point (e.g., 438.065)
- Press E
More detailed programming is outlined in the scanner operating instructions, which you can download and print here:
http://www.uniden.com/pdf/BC60XLT-1om.pdf
For a comprehensive database of active frequencies in your area, and a lot of other useful scanning information, visit:
www.RadioReference.com
Bill B
How to program channels
The BC60XLT is limited to ten channels. Programming is best described in the factory manual, which you can download and print here:
http://www.uniden.com/pdf/BC60XLTom.pdf
Bill B
Hand held scaner
To enter a known frequency into the scanner's memory:
1. Power the scanner ON.
2. Press MAN to stop scanning.
3. Enter the number of the channel to be programmed (1 through 30) - OR - press the MAN key repeatedly to advance to the desired channel.
4. Enter the frequency including decimal point (ex: 146.25).
5. Press E to enter the info into memory.
6. Repeat steps 2 through 5 to program other channels.
Need the manual? You can download/print it here:
http://www.uniden.com/pdf/BC60XLT-1om.pdf
For a comprehensive database of active frequencies in your area, and a lot of other useful scanning information, visit:
www.RadioReference.com
Bill B
Need manual
Press MAN. Enter the channel you want, then press MAN. Enter the frequency you want to program, press E enter ,,,,hope this was helpful...
How do i program my sc150b
To program your scanner:
- Turn the scanner ON
- Press SCAN
- Press DCBNK
- Press HOLD
- Enter the number of the channel you wish to program
- Press HOLD
- Enter the frequency, including the decimal point
- Press E
To program another channel, repeat the above - starting with channel number
Need the manual? You can download/print it here:
http://www.uniden.com/pdf/SC150Bom.pdf
For a comprehensive database of active frequencies in your area, and a lot of other useful scanning information, visit:
www.RadioReference.com
Bill B
Uniden 30 ch scanner i have locked out all channels.
Each channel with the zeroes means that it is a blank - with nothing programmed into it. Going to any one of them and programming a frequency will get rid of the zeroes and switch off the lockout. It's picking up weather, so it's working. Sounds like you just need to find and program active frequencies for your area, and the place to find them is:
www.RadioReference.com
If you need it, you can download and print the manual for the BC60XLT-1 here:
http://www.uniden.com/pdf/BC60XLT-1om.pdf
Bill B
How to program the frequencies
To program the majority of non-trunking Bearcat scanners,\:
- Power the scanner ON
- Press MANUAL to stop scanning
- Enter the channel # to program followed by MANUAL (OR just press MANUAL repeatedly to advance to the desired channel).
- Enter the desired frequency, including the decimal point.
- Press E (ENTER)
If these steps don't work with your scanner, please provide your model number and I'll get back to you with specifics.
Bill B
Not finding what you are looking for?
