20 Most Recent Uniden Bearcat Pro PC68Elite 40-Channels Base CB Radio - Page 3 Questions & Answers

I have Manuals with the update Sheet $14.95 each (706)270 3829

If you get clear audio when close to the receiver, it would appear to be a problem in either the antenna or the receiver. Try a different antenna or relocate the antenna. If you adjusted the VSWR low it doesn't mean the power is radiating correctly. Verticals should be on roof, with roof as ground plane. Mounting on mirrors is ok, but doesn't work as well. Also, if you have sheet metal near the antenna, it acts as a ground reflector and can distort or block the waveform. You might also try it with a different receiver, in case yours has a faulty pre-amp stage. It could also be a power amplifier problem in the transmitter, where it shows 5 watts but isn't putting out that amount. You can check it with an RF watt meter.

Trying to wire a dm-452 4 pin mic to a 5 pin uniden ... - Fixya

www.fixya.com/.../t22723929-trying_wire_dm_452_4_pin_mic_5_pin

Jan 6, 2014 - trying to wire a dm-452 4 pin mic to a 5 pin uniden washington -Uniden Bearcat Pro PC68XL ... SOURCE: trying wire a superstar dm-452.

How to wire a superstar DM-452 to a five pin uniden and ...

www.fixya.com/.../t26060852-wire_superstar_dm_452_five_pin_uniden

36 mins ago - how to wire a superstar DM-452 to a five pin uniden and washington - Uniden CB Radios question.

Wire superstar dm 452 mic - Answer

www.dqrkc.com/search/...uniden...pro.../wire_superstar_dm_452_mic

... to a 5 pin how to wire a dm-452 superstar 4 pin mic to a 5 pin uniden washingtonit's not possible to wire 4 wire mics to the uniden 5 wire radios without ...

Uniden Bearcat Pro PC68XL 40-Channels Base CB Radio ...

what is your location ? https://www.rylwy.com/diy-magnetic-loop

Uniden Pc76xl Manual FREE Download - Ebookread..click on this if t don't work just copy and paste and put it into google. hope this helps you out.let me no how you get on. i was on the cb for over 30years myself so good good luck 10.4 and out.

If you have access to the Internet then Google that particular county government radio frequencies and try the one that it gives you . Hf,vhf,uhf??

https://www.manualslib.com/download/334326/Uniden-Bc200xlt.html Download user manual and read instructions at page-9, your problem will be solve.

hi, it looks something went wrong with the program. I will suggest to make a hard reset to the unit. if its not helping - maybe you will need to reprogram the unit, regards, Daniel https://www.rylwy.com/carbon-antenna

Press scan then press key pad numbers to enable banks. All of your programmed frequencies may have been erased.

An older uniden for a frequency range between 100 and 199 mhz may expect you to interpret the frequency being shown as 1 followed by other digits on your display. For example a frequency of 145.350 may expect you to mentally add the printed "1" and digits 45350 giving the total frequency. This saved the manufacturer from having to purchase another digit to display the frequency since it is always 1 to start with.

https://www.manualslib.com/manual/184910/Uniden-Uh089sx.html

search ebay for "regency r1070 scanner antenna" and many will pop up. Also Radio shack..

Why do you need to do that? There is no provision for a process that totally resets that scanner.

i need radio phone codes for my scanner.

Have you tried using an external speaker? If you are using one, try disconnecting it and see what happens. If you can't hear anything after these easy tests, you have something wrong inside that needs looking at by a qualified technician. Believe me when I say there is nothing that you can do to repair this problem if it is internal to the radio.

Without knowing the frequencies, it is hard to diagnose. If you are trying to listen to police, fire, govt freguencies, the transmissions are scrambled or use split multiple frequencies. You will not be able to receive any voice without the key. If channel jumping is used, you will only hear a veryquick burst of audeo if you are lucky enough to be listening to the correct fequency asthe signal travels by onto the next frequency.

not sure if i am right in saying this,but when in scan mode you wont hear anything until if finds a channel that there is something going on then it will stop on that channel. please let me know if this is what you are asking.

It may need a new little mem, battery check it ouuuut !