Emerson EWC1303 13 in. TV/VCR Combo - Answered Questions & Fixed issues

Your over voltage circuits(hi-voltage and low voltage) are defective.When the voltage exceeds the specs it shuts off the tv.Unless your a service tech,you can't fix this.There are components on the main circuit tha t have to be changed.Sorry, no easy fix.

You have built-in features that correspond between the TV and The Hand held controller designed by Emerson. Universal remotes are lacking some features that are necessary for full function of the TB. In your case, you may be required to replace the hand held unit with another exactly alike and with all of the functions you are accustomed to.

Try doing the auto scan first to get all the possible channels.. Usually the Add/Delete function applies once the TV knows what channels are out there to add or delete.

I would just replace the TV unless you have the skill and tools required to fix the problem with the old one.

turn on the machine. use your figure push on the cassette, when you feel the cassette can't go any farther (don't jam it),and hold it there. press the eject button, you may have to try this couple of times in order for the cassette to come out.
the cassette deck need to have the drive belt change.

This first link provides the procedure on how to program the remote http://www.mydish.com/support/program-to-tv-code-non-basic?WT.svl=contentArea This second link will provide you the codes needed to program the remote to the TV (The top line would be your remote model # you will find this number on the back of your remote, make sure that is the one you enter) http://www.mydish.com/support/apps/remotecodes.aspx?WT.svl=leftnav If you need further assistance please let me know. Once you have obtained the codes that can address to your television you follow this procedure to program the remote. (Which is the procedure provided on the first link) Press and hold the clear TV button at the top left hand side of your remote for 5 seconds (all the other clear buttons will light up) once this happens enter the code followed by the # button on your remote, the clear TV button at the top will light up 3 times, this means the remote has been programmed. You can verify the remote has been programmed by trying to up the Volume, once you verify it works be sure to press the SAT button at the top left once (to set remote back to SAT mode and avoid other problems) Feel free to contact me at: [email protected] if you need further assistance.Kimberly EscobarSocial Media RepresentativeDISH L.L.C

Disconnect the VCR and leave the TV on and see whether the TV gets off. If it gets off, the timer in the TV is the one that has to be reset. I do not think there is any way a TV can be switched off by a VCR, unless the power supply is controlled by VCR.

POWER SUPPY BOARD

Hi:
Check on your remote for a button labeled CC or check you setup meny under setup for the closed captioned option and set to off posistion.

Hello
If your other TVs work on the same antenna, and only this Emerson doesn't work with it, eiter your TVs tuner inside, or it tuning has some trouble. Check by put the set to autotune refering to its user manual. Check whether the cable socket is tight or not.
If these are correct, replace its tuner, [it is inside the circuit board], with same type and number. OK.

You may find a bad capacitor near the powerline regulator. This powerline regulator will have an STR-XXXX number. And if that is not enough, you will surely have two or three resistors that have changed values. These combonation TVs are very, very difficult to keep operating. You may have a service person repair this....and then in a month the TV will act up again. This is good advice. You decide what to do next. Thanks for asking and show a few hands of support.

Hello

Comcast remote codes for Emerson TV are:-

?
10154, 10451, 10236, 10463, 10180, 10178, 10171, 11963, 11928, 11913, 11911, 11909, 11905, 11665, 10282, 10280 10270, 10183, 10181, 10179 10177, 10038, 10019
You have to check with each code, until you find which code sets for your TV

?
programming TVcontrol
The Comcast Digital Adapter remote control is pre-programmed at the factory to operate the Digital Adapter. The Comcast Digital Adapter remote also contains a universal TV library to allow you to control the Power and Volume of your TV.
1. Turn on the TV
NOTE: Please read steps 2 to 4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.
2. Press and hold SETuntil the Red Light blinks twice, then release SET.
3. Locate the code for your device in Manufacturer's Codes on the back of this user guide. Brands are listed in alphabetical order with the most popular codes listed first.
4. Enter the first five-digit code for your TV. If you perform this procedure correctly, the Red Light will blink twice
NOTE: If you enter an invalid code, the red light will display one long blink and exit the programming mode. Repeat steps 2 to 5 with a valid code.
5. Aim the remote control at your TV and press Power once. The device should turn off. If it does not respond, repeat steps 2 to 4, trying each code listed for your brand until you find one that works. If it still does not work, try Searching For Your Code.

?
Searching For Your Code
If your brand of TV does not respond to the remote control after trying all of the codes listed, or if your brand is not listed at all, try searching for your code.
1. Turn on your TV.
2. Press and hold SETuntil the Red Light blinks twice, then release SET.
3. Enter in 9 - 9 - 1. The Red Light will blink twice.
4. While pointing the remote control at the TV and press and release the CH + key until the TV turns off. (Note: You may need to press [CH+] numerous times).
NOTE: In the search mode, the remote control will send IR codes from its library to the TV.
5. Press SETonce to lock in the code. The Red Light will blink twice.
OK.

Hello

You just buy one Philips Universal Remote Control Model [ CL 034]. Your emerson is lited in its codes. I'm sending these codes and procedings alongwith. Ofcourse you have to try with a lot of codes, since Emerson have a lot for them. Try with patience.

0002 0502 0006 0115

0506 0706 0520 0906 0316

0505 0614 0324 0924 0626

0826 0027 0327 0128 0228

0632 0134 0247 0605 0705 0805

0703 0903 0004 0519 0106 0104
0304 0604 0804 0005 0105 0305

Direct Code Entry

1. Press and hold the CODE SEARCH

button until the red indicator stays

on, then release the CODE SEARCH

button.

2. Press and release the desired Mode

button (TV, VCR, etc.). The red

indicator blinks, then stays lit.

3. Enter the 4 digit code from the code

tables. Note: after a valid code entry,

the red indicator turns off. For an

invalid code, the red indicator

flashes.

4. With your device on, press

CHANNEL UP. If the device

responds, no further programming is

required. Note: If some buttons do

not operate your device, try one of
the other codes for your brand.
Ok.

sounds like it is overheating and/or malfunctioning. may need to be sent in for repair. no other option, sorry..

Hi.

You May download this manual from this website

click here

Its in PDF format, click the diskette icon to save it in to your computer


hope that helps

You can buy a brand new remote control here:


http://www.electronicadventure.us/Merchant2/merchant.mv?screen=prod&store_code=EA&product_code=N0162UD

Use Funai codes. Made by Funai.

Sounds like the "Mode Switch" has gone faulty...

need remote coding for a emerson ewc1303

its very difficult to get digital stations if youre using an indoor standard antenna , unless you have a SPECIAL DIGITAL ANTENNA for indoors , but I suggest an outdoor antenna , the higher ,the better to locate digital stations , AJ