20 Most Recent
E-Machines eMachines W2686 PC Desktop - Page 2 Questions & Answers
I recently formatted a second harddrive on my
Hello.
Not certain if you still need this, but ...
To find and install the driver for the simple
communications controller:
Go to Device Manager and click on the pci simple
communications controller
Go to Properties and then Details. You will see a code like
PCI/VEN_8086&DEV_27D8&SUBSYS...
The VEN code means vendor and the DEV code means device: in the example the
vendor is 8086 and the device is 27D8.
Once you have the two codes, go to www.pcidatabse.com. Enter the two codes and you should get
the name of your hardware.
From there, you can search for a driver download for your
hardware
Hope this helps.
My batt went dead and I did not record my bios
You should be able to either download a replacement disk or request one from the manufacturer. I think that or ebay is your best bet. Since that is not a new computer it may be tuff to get the disks.
11/22/2009 11:14:40 PM •
E-Machines...
•
Answered
on Nov 22, 2009
Adobe.stops.and.go.media.player
Bro, I can fix this
Adobe is the best! But VERY EXPENSIVE
This is my best advise to get everything you need.
Go to www.Myspace.com/KyleGallas to watch a video of a Custom Gaming
Computer with Adobe CS4 installed...The PC has like $4,000 retail for
like $659. It comes with a ton of extras like 133 Nintendo DS Games,
Fallout 3, Adobe CS4, MS Office Ultmate 2007, Roxio Ultimate 2009...and
more...Nothing is trial-ware but yours forever.
When I try to down
hi there,
no icons after downloading,it was not succesful,try to download again,first run the application file then after 100% completion, run the installation file on this you are subject to ask by website where you want to install,select or browse the location to C:/Program file/ install on this location after downloading for several minutes check this on program file,going to my computer,leftr click the C:/ then explore, find program file left click
and explore on program file find your game and click it,to explore and left clik the icon send to desk top,regards
Lockedout. vist 32, no user but me.
Use ERD Commander and use locksmith to change "your" password (if it will let you), click OK and reboot the PC, use the new password to log in.
If that does not work then ERD commander has not attached itself to Vista's registry so you will need to download the latest version.
It will be in ISO format so just use burning software to burn it to CD.
Good luck.
Emachine will not come on
Reseat the power cord that is on the motherboard. Sometimes if you pull that cord from the motherboard (be careful there is a clip that is holding it to the board) wait about 1 minute then plug the cable back onto the motherboard your machine will possibly turn on. Also unplug your power supply cord from the computer when you do this. The other issue could be that the battery on the motherboard is dead.
I’m happy to assist further over the phone at
https://www.6ya.com/expert/barbara_87cfe34e34050f26
Dont show sceen when booting up then shuts down
There may be different reasons for this to happen first of all to check whether this is a problem of Hardware or software i would suggest you to switch on the system and immediately press the F2 or Del key the system will enter the CMOS setup if the system shuts Down in CMOS screen then it is a problem with your Hardware
If not than it is a probably due to Operating System Corrupt in that case you have to reinstall the operating system
it may also be due to Resource conflict where you have added a new hardware to your system
W2686
Your problem would not be with a battery, but the power supply. Try plugging into a different outlet just to make sure, but sounds like you may need a new power supply.
I have an emachines t5226 with vista. it will not
hi! if your pc is still powering then theres no problem with the PSU, if your pc boot and have a display on your monitor then theres no problem with your VGA card and RAM but if your PC don't have display then you must check your VGA and RAM it maybe a faulty hardware. and next thing you do is check if your HDD is stillworking and make sure you have a bootale CD with you..good luck
Not finding what you are looking for?