20 Most Recent
RCA RCU600M Remote Control - Page 4 Questions & Answers
I need the codes to program my Innovage Jumbo
As there are no specific codes for the Dynex TV you have the choice of either using the Auto or Learn method. The following are instructions for both:
AUTO Method
1. Press & Hold (about 3 sec.) the [DEVICE]
button on the JUMBO Remote....llight will stay solid.
2. Now just
press the [POWER] button (only) ONCE while pointing at the device...it
will start sending codes approximately every second. (Don't keep
pressing the power button as instructions indicate.)
3. TIMING IS
EVERYTHING HERE. (It may take 5 minutes to find your devices code.)
4.
AS SOON AS the power goes off...press the [ENTER] button on the JUNBO
Remote.
5. Now pressing the [POWER] button should power up/down the
device.
---- any buttons not programmed will have to be handled
using the LEARN method ---
LEARN Method
1. Press &
Hold (about 3 sec.) the [DEVICE] button on the JUMBO Remote....it'll
stay solid.
2. Press the [LEARN] button on the JUMBO Remote. (light
will immediately blink rapidly.)
3. Now Press the {NEEDED} button to
program. (light will stay solid)
4. Now (1 to 2 inches away) have the
ORIGINAL Remote pointed at the JUMBO Remote and press the {DESIRED}
button on the ORIGINAL Remote.
5. It blinks rapidly while
sending...then a slower steady blink once "LEARNED" correctly.
***
Not all buttons work properly with the "LEARN method". Some you will
need to "associate" with an alternate button on the JUMBO Remote. *
I need the programing code for a coby tv
I noticed the Colby is not in the list of codes. In the case of a code not showing up in the list, I would suggest trying the Auto Code Search. The steps below will help you.
1. Turn on the component (TV, DVD, etc) you want the
remote to operate.
2. Press and hold the CODE SEARCH key
until the indicator light comes on.
Then release the CODE SEARCH key.
3. Press and release the component key that
corresponds to the component you want
the remote to operate (TV, VCR, DVD,
DBS·SAT, CABLE, AUDIO). The indicator
light blinks once and remains lit.
4. Aim the remote at the component and
press the ON•OFF key once. The remote
automatically sends every code for
the specified component one at a time,
with the three-second delay between
each code. Keep the remote aimed at the
component throughout this process.
5. As soon as the component turns off, you
must press the ENTER key immediately
so the remote stores the correct
code. If you do not press the ENTER
key within three seconds, the remote
sends the next code in the list, and you
will have to start over from step 2.
Good Luck,
NOLA Tech
Need codes for symohonic tv
Hi there,
Well first of all you can try 0091, 0053, 0234, 0155, 0162, 0171 or 0180 If further your remote won't recognized the TV then please post some comment.
Good Luck!!
Thanks
I need to code a magnovox vcr into my innovage
The codes for a Magnavox VCR are: 021, 060, 062, 104, 106, 115, & 124.
To program your remote by entering a code, follow these steps:
- Turn on your VCR.
- Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
- Press the VCR button on the remote so that the LED blinks once and then remains solid red.
- Enter the first set of 3-digit codes from the list. The LED will
blink once every keypress. After the 3rd digit, the red LED will turn
off indicating that the code was recognized for the device. If the code
was not compatible, the LED will flash several times and you need to
return to step 2 to try that code again or to try the next code in the
list.
- After the LED has turned off, aim the remote at the VCR and press
ON/OFF. If the device turns off, you have used the correct code and the
remote was successfully programed. If the device does not power off,
return to step 2 and try again with the next code in the list.
I hope that helps.
Is there a code to control my LG 42
003,004,006,011,019 027,039,040,041,051,071,083 027,037,050
Hope this helps you out.
Cheers Little Dish Fitter
Not finding what you are looking for?
