Top 20 Bush 2871NTX 28" TV Questions & Answers

Look on Amazon for a pattern dedicated remote for your tv. They aren't expensive and will allow you to access the set's menus.

If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common codes to check devices with different brand TVs are given, in the order of the device's brand name list in alphabetical order. Pull up older posts. Surf the site with patience. http://electro-medical.blogspot.com/ http://remotesearch.blogspot.com/ http://electrohelponline.blogspot.com/

Flashes of standby light are fault indications. Form the number of flahes occur at one time switch ON, you can get an idea about the faulty circuit stage inside the TV. If you wish to get more details, check this link. http://electronicshelponline.blogspot.com/ Selecting the view option, either to Mosaic / Time slide, can be selected by the drop-down list, at the top left of the display window, will make surf easy. You can also do a search, by type in the brand name/model number/IC used, in the search box at the top right of the display window.

0092,0096,0091,0094. Check these codes. If you wish to get more details, check the sites linked here. Setup code list, and setup procedure to many popular brand remote controls are given. http://electrohelponline.blogspot.com/ http://remotesearch.blogspot.com/ Selecting the view option, either to Mosaic / Time slide, can be selected by the drop-down list, at the top left of the display window, will make surf easy

Download its user manual. It had all details. http://www.bushhog.com/manuals.html Try this link.

It will be difficult to unlock it without its remote control.

it could be a problem in digital tune,tried with resetting.

Bush CT-219 Remote please app send sir

Replace its memory IC and clock oscillator.

I suppose we get what we pay for. I would do exactly that. A decent amplifier and off you go. The sound quality going to the external amplifier is as good as any other system it is just the internal speaker/amplifier is a bit basic.

Determine if there is a source of interference such as flourescent lights. Turn all electrical items off and switch them on, one at a time to see which is causing the problem. Also try covering the IR pickup window on the TV with some card to see if it is due to external interference or it is an internal problem.

That happens with magnets and could be caused by the magnets on the speakers, some green or purple stay forever, but some disappear when you unplug and unplug the tv repeatedly or with other magnets.

0157 is the code for Bush tv's

You should check and see if the sleep timer has been set

Unplug it from the wall for half an hour, plug it back and start it for another half an hour. This way the demagnetizer coil inside it will have the time needed to act. If necessary repeat several times. If you don't see an improvement after the third cycle the coil is inactive and it must be fixed.

depends where you live , in Europe try CPC or RS components

This is the best solution for your problem as a 40 year experience with wires etc. Go to the source of your cable signal connector . Open it and clean the terminals with emery paper , sand the end of the cable shiny clean from corrosion , get a new barrel connectors with gold terminals if possible lengthen the ends of the cable , insert and tighten good, use thick rg-16 or rg 40 cable with good insulation ends crimped professionally with a crimpier or buy ready made , not from dollar store. Get a gold plated professional splitter if you need one or two , it will cost about 15 or more each . Make the cable runs as short as possible, using the thick good cables. If needed get a signal magnifier. From radio shack or the source etc. Connect them good and tight . Ground the splitters . Problem solved , you will get crystal clear channel 2 to 7 including 3 and 4 . Isolate the TV cable from other cables and power wires. Vitally

code for universal remote is 022 try it ok

Buy a universal remote. Find the code, program it, viola!

try to check horizontal output ic