20 Most Recent Kenmore 51173 Elite Stainless Steel 29.8 Cu Ft Refrigerator Side-by-Side Freezer, Energy Star - Page 4 Questions & Answers

Either there is a frozen or a clogged water line.Or the water lines need to be replaced.

It is possible that there is a switch for the dispenser light on your Kenmore Coldspot refrigerator. Some models have a separate light switch that may be located near the dispenser or inside the refrigerator compartment. You can try checking the user manual for your specific model or contact Kenmore customer service for more information. If the dispenser light still does not turn on after checking for a separate switch, there may be an issue with the wiring or control board for the dispenser. In this case, it may be best to contact a professional technician for further diagnosis and repair.

There are a few possible reasons for the ice build-up in the area behind the ice maker and above the fan, even if there are no visible coils in that area. Here are some potential causes to consider:

1. Blocked Drain: The defrost cycle of a refrigerator is designed to remove excess moisture from the freezer compartment, which typically drains out of the freezer through a small drain hole and into a collection pan located beneath the refrigerator. If the drain becomes blocked, the excess moisture can accumulate in the bottom of the freezer and eventually freeze, leading to the ice build-up you described. To check if this is the case, you can try locating the drain hole (usually near the back of the freezer, near the bottom) and clearing any debris or ice that may be obstructing it.
2. Faulty Defrost System: Another possibility is that there is an issue with the defrost system itself. If the defrost heater, thermostat, or timer is not functioning correctly, it can lead to excessive ice build-up in the freezer compartment. While you mentioned that the coils appear to be defrosted, it's still possible that there is a problem with one of these components that is causing the ice to accumulate in a different area.
3. Poor Air Circulation: A third potential cause is that there is inadequate air circulation in the freezer compartment. If the freezer is too full or if items are blocking the vents, it can prevent cold air from circulating properly, leading to pockets of warmer air that can cause excess moisture to accumulate and freeze. It's worth checking to make sure that the freezer is not over-packed and that there is nothing blocking the vents.
4. Water Leak: Finally, it's possible that there is a water leak somewhere in the refrigerator that is causing excess moisture to accumulate in the freezer compartment. This could be due to a damaged water line or valve, a faulty ice maker, or a damaged door seal that is allowing warm, humid air to enter the freezer. If you suspect a water leak may be the cause, it's best to have a professional diagnose and repair the issue.

Overall, it's hard to say for sure what is causing the ice build-up without further inspection, but these are some common possibilities to consider. If the issue persists, it may be worth calling a professional to diagnose and repair the problem.

Based on the information you provided, it sounds like your Kenmore refrigerator is operating normally. Most modern refrigerators are designed to cycle on and off in order to maintain the temperature inside the fridge and freezer compartments. During the "on" cycle, the compressor runs and cools the refrigerant, which in turn cools the air inside the fridge and freezer. During the "off" cycle, the compressor stops running and the refrigerant flows back to the compressor to prepare for the next cycle. The length of the on and off cycles can vary depending on factors such as the ambient temperature in the room, the amount of food inside the fridge, and how often the doors are opened. However, it's normal for a refrigerator to cycle on for around 10-15 minutes and then off for around 20-30 minutes. If the temperature inside the fridge and freezer compartments is staying at the correct levels, then there is likely no cause for concern. However, if you notice any unusual sounds, odors, or fluctuations in temperature, it may be worth having a professional technician inspect the refrigerator to ensure it's functioning properly.

No idea. Try asking Kenmore.

Here's a Manual..... https://www.searspartsdirect.com/manual/2k1ac3cenf-000582/kenmore-10651783412-side-by-side-refrigerator-parts you can download a pdf too

Based on the symptoms you described, it is possible that the main control board of your Kenmore refrigerator is faulty. The fact that unplugging and replugging the fridge appears to have temporarily fixed the problem suggests that the issue could be related to the electrical components on the board. The ER DH error code you received indicates that there is a problem with the defrost circuit. This circuit is responsible for melting any frost that may accumulate on the evaporator coils in the freezer, which can lead to a build-up of ice that affects the fridge's ability to cool. A faulty main control board can cause issues with various parts of the fridge, including the defrost circuit. If you have already tried unplugging and replugging the fridge and the error code persists, it may be worth contacting a professional technician to diagnose the issue and possibly replace the control board if necessary.

fixya doesnt sell or manufacturer products -----online parts 1000s of sites or appliance shop in your area

All refrigerators run and then turn off repeatedly, it's how they maintain the temperature. If they seem to run too often, this can be caused by a loss of refrigerant caused by a leak. Your door seals could be worn, causing a leak and requiring the unit to run more frequently. Anything restricting air to the unit can cause problems, including dust, pet hair, lack of ventilation, etc.

The evaporator coils or the evaporator fan motor is broken or the defrost thermostat is no good or an issue with control board or a problem with the temperature sensor in your fridge.

There is a communication issue with the display board and the main unit.

You may have a problem with the gear assembly for the freezer tray on your Kenmore Elite refrigerator. The gear assembly is responsible for supporting the rear of the basket and keeping it in place. Your description sounds like your gear assembly may be an older generation and may not have screw holes for attaching the gears to the support arm sliders. The gears may be designed to be snapped into place on the support arm sliders. The plastic tab you mentioned at the back of the slider is likely the attachment point for the swivel hub on the gear. To attach the gears, align the swivel hub with the plastic tab, then gently push it in until it snaps into place. The tab may be jammed or stuck; in that case, you can gently pry it loose with a small flat-head screwdriver. If you continue to have trouble installing the gear assembly, consider contacting Kenmore's customer service for further assistance. They can provide you with a detailed exploded parts diagram or even a video tutorial on installing the gear assembly properly

20.7 cu ft.

What Are Some Specifications of the Kenmore Coldspot ...

https://www.reference.com > World View The Kenmore Coldspot 106 is a 20.7-cubic foot side-by-side refrigerator with a reverse osmosis Pur water filter, ice maker and digital controls.

If your appliance is displaying an error code that flashes "H" and "F" repeatedly, it may indicate a problem with the temperature or humidity in the appliance. This could be caused by a malfunctioning sensor or a problem with the control board. To troubleshoot the issue, you can try the following:

1. Check the door seals to ensure that they are clean and in good condition.
2. Make sure that the appliance is level and that there is sufficient ventilation.
3. Check the temperature and humidity settings to ensure that they are set correctly.
4. If the problem persists, it is best to have the appliance checked by a professional. They will be able to diagnose the problem and suggest the appropriate repairs.

It is important to note that this is just a general guide and the specific cause of the error code may vary depending on the make and model of your appliance. Be sure to refer to the user manual or contact the manufacturer for specific troubleshooting steps.

If the control panel on your Kenmore dehumidifier is flickering on and off, there could be a few potential causes for this issue:

1. A loose or damaged control panel display ribbon cable. This cable connects the control panel to the main circuit board and any damage or looseness could cause the control panel to malfunction.
2. A faulty control panel display. If the control panel display is not functioning properly, it could cause the control panel to flicker or not work at all.
3. A faulty main circuit board. The main circuit board is responsible for controlling the various functions of the dehumidifier, and any issues with it could cause problems with the control panel.

To troubleshoot this issue, you may want to try the following:

1. Check the control panel display ribbon cable for any visible damage or looseness.
2. If the cable appears to be in good condition, try resetting the dehumidifier by unplugging it and then plugging it back in.
3. If the issue persists, you may need to contact a professional for further assistance in diagnosing and repairing the issue with your dehumidifier.

This is most likely due to the defrost thermometer. However, proper testing is recommended by a technician to be sure. It is located at the back of the inside freezer cabinet. You will have to remove the shelves and drawers to access a panel secured with hex screws. When the panel is off, the small round silver piece with a red and black wire is the defrost thermometer. Be careful of the fins around the coils as they are extremely sharp.

F01 is a general error code that indicates a problem with the electronic control board. The clicking sound you are hearing may be the result of a failed component on the control board. It is possible that the control board may need to be replaced. However, it is also possible that the issue could be with another component in the dryer, such as a faulty relay or a damaged wire connection. To troubleshoot the problem, I would recommend checking all of the wire connections to ensure that they are secure. You should also check the relay and make sure that it is functioning properly. If the issue persists, you may need to consider replacing the electronic control board. If you are not comfortable working on the dryer yourself, I would recommend contacting a professional appliance repair service. They will have the tools and expertise needed to diagnose and repair the problem.

https://removeandreplace.com/2015/05/27/freezer-drain-frozen-water-dripping-into-refrigerator-how-to-fix/

Sears is the best place for parts and they also have diagrams. https://www.google.com/search?q=Kenmore+side+by+side+Refrigerator+Model+795.5103+parts& ..