Alpine CDA-9847 CD Player - Answered Questions & Fixed issues

please a170 AL2199w0619724 audio 10 code???

check the speekar & wiring

Are you using an amplifier? If so, it sounds like you are using the blue wire, which is a power antenna remote turn on, in stead of the blue/white wire to turn the amp on. The blue wire turns off when leaving tuner mode, turning the amplifier off also.

If you can, try checking your speakers and speaker wires for any shorts or grounds.

Confirm this wiring for 2000 Nissan Altima Car Stereo Radio Wiring Diagram

Radio Constant 12V+ Wire: Pink
Radio Switched 12V+ Wire: Blue
Radio Ground Wire: Chassis
Radio Illumination Wire: Red/Green
Radio Dimmer Wire: Red/Yellow
Radio Power Antenna Trigger Wire: Green/White
Radio Amplifier Turn On Trigger Wire: N/A
Front Speakers Size: 4′ x 6′ Speakers
Front Speakers Location: Doors
Left Front Speaker Wire (+): Brown
Left Front Speaker Wire (-): Black/Red
Right Front Speaker Wire (+): Light Green
Right Front Speaker Wire (-): Black/Yellow
Rear Speakers Size: 6 1/2′ Speakers
Rear Speakers Location: Rear Deck
Left Rear Speaker Wire (+): Orange
Left Rear Speaker Wire (-): Black/Pink
Right Rear Speaker Wire (+): Blue
Right Rear Speaker Wire (-): Black/White

Hope helps.

one wire is power on is acc which is memory cant have both hooked up to one power wire it has to be one on power thats on all the time and one on a wire that only has power when ignition is on if this is what you have already done then switch the two wires that will solve your problem

there should be a switch on bottom of the deck to change the frequency selection.

first, you might want to check your speakers and speaker wires to make sure you have no grounds, shorts or bare wires. if they all check out, the output ic is located behind the big heat sink (an aluminum piece of metal with fins) on the back of the deck.

Welcome to fixya

Hello

I have a solution for this

Press Ok, Accept or replay so we may get started

Your pre-solution is coming up shortly

PLEASE REPLY OR LEAVE COMMENT TO CONFIRM YOU RECEIVED THIS EMAIL

My name is Bruce

it sounds like you are using an amplifier. if so, make sure you are using the blue/white wire to turn the amp on instead of the blue wire. the blue wire is antenna remote and turns off when leaving tuner mode. the blue/white wire is amp remote.

uh oh, check the fuse and fusable links, i hope you had it fused

Find the fusebox, then the one marked ACC (accessories, this way it can run with the key turned backwards as well like all radios would). Pull the fuse and test for power. On the side with no power is where you want to install the CD's power wire. Ground the ground wire somewhere firmly. Reinstall the fuse and turn the key backwards and it should run.

Doesn't it have an instruction manual?

The reason I ask is some can be very different. Some you hook to the power and they have a wire (mine was orange) which says to hook to the accessories.

The rest will be speaker wires. Just keep them phase matched.

http://www.mercedes4arab.com/vb/index.php

search here

you need to have the yellow wire going to a constant power source for the radio to retain memory when the key is off.

There is a small switch on the unit's housing, switch it to "Norm" position.

try this

Setting the AUX Mode (V-Link)
AUX IN ON / AUX IN OFF (Initial setting)
You can input TV/video sound by connecting an optional Ai-NET/
RCA Interface cable (KCA-121B) or Versatile Link Terminal (KCA-
410C) to this component.
You can change the AUX name display when AUX ON is set. Select
the AUX name by pressing g or f. Then press BAND.
If the KCA-410C is connected, it is possible to select two AUX
names.
• Via KCA-410C, up to 2 external devices with RCA output can be
connected. In this case, press SOURCE/POWER to select AUX
mode and then press BAND to select your desired device.

You need to find the rest button on this unit and press it for 4 sec, it is usually located behind the face

Link to a PDF Owners Manual for the Alpine CDA-9847...


http://vault.alpine-usa.com/products/documents/OM_CDA-9847.PDF

"Setting Time" is found on Page 7.

Try code 45553

From the manual...

Setting Time
1 In the Clock priority mode, press and hold TITLE for at least 2 seconds while the time is displayed. The time indication will blink.

2 Turn the Rotary encoder to adjust the hours while the time indication is blinking.

3 When the hour has been adjusted, press the Rotary encoder.

4 Turn the Rotary encoder to adjust the minutes while the time indication is blinking. The time is automatically set 5 seconds after the minute adjustment. The time can also be manually set by pressing the Rotary encoder.

• To synchronize the clock to another clock/watch or radio time announcement, press and hold the Rotary encoder for at least 2 seconds after setting the “hour.” Minutes will reset to 00. If the display shows over “30” minutes when you do this, the time will advance one hour.