MFJ 854 RF Current meter, 30mA-3A - Page 9 - Answered Questions & Fixed issues
My husband is out of town and I want to use the
the blades are usually in the case.its simple just place what you want to cut in front of the blade with the metal bottom of saw touching the object to be cut and pull the trigger.
1/29/2010 6:11:24 PM •
Hand Tools
•
Answered
on Jan 29, 2010
•
142 views
How to set up replacement blades in a DeWalt DW677
I have a Hitachi planer that came with an unlikely looking fixture for setting the blades. Perhaps your DeWalt came with one of these too. Looking at the thing you would wonder what the heck it was. If no such fixture was included, you might try a "Jointer Pal" This is a magnetic device that is designed for use with a jointer, but would probably work on your planer.
1/27/2010 9:14:23 PM •
Hand Tools
•
Answered
on Jan 27, 2010
•
528 views
I have a Rapitest pipe/wire and stud finder but
If its like my one (Different brand) you simply switch on and adjust fine control till the lamp just comes on then turn opposite way till lamp just extinguishes, Make suer the unit in pressed onto the wall.
1/26/2010 7:59:05 PM •
Hand Tools
•
Answered
on Jan 26, 2010
•
3,080 views
Stanley carpet knife cannot get the blade to
there not!! suppose to slide easily i used to lay carpet for a living those blades are made to stick out or in without slpping to insure even and straight cuts
1/21/2010 5:44:13 PM •
Hand Tools
•
Answered
on Jan 21, 2010
•
215 views
Have a craftsman tool chest cannot figure how to
Is this a stack of metal tool cabinets? Once you have released it in front, perhaps you just lift it up. I think the tabs in the back just keep it in vertical alignment. Gravity does the rest. I have one of these, and it's been a while since I assembled it, so I'm not certain.
1/19/2010 8:01:19 PM •
Hand Tools
•
Answered
on Jan 19, 2010
•
198 views
My stud finder flashes back and forth from bulls
Hi get small piece of sheet rock scrap from home dopet or low's 3x6or8 scraps are buy the sheetrock they use for stacking the rock 1 piece of 2x3or4 from scrap cart,nail/screw rock to wood with 1 nail or DW screw practice finding nail/screw with your studfndr mark with small line with pencil when u find the center, use stdfndr on your wife see what happens should flash red, good stdfnding we will go hi ho da cherriieeoo gstdfndingwwg chorus
1/12/2010 11:54:12 PM •
Hand Tools
•
Answered
on Jan 12, 2010
•
186 views
Faulty Record carpenters vice
Hi pal this is what u have to do, put a plastic garbage bag & about 15 sheets of newspaper on the floor below the vice spray with "liquid wrench" with red tube on the nozzle spray all around nooks underneath sheild the vice with a piece of cardboard os you don't spray the walls,floor or ceiling let stand 5 min. then bang with a 24" piece of 2x3 or 2x4, wrap a piece of rag around the handle base then use a 12" pipe wrench over rag/base tap & switch the wrench back & forth, "do not bang" the vice wooden handle it can brake be gentle spray & tap/bang pipe wrench make sure the handle is covered with the rag so u don't mar the wood handle with the 2x3 4, remember tap n turn the wrench around be patient, tap the back back of the vice handle while putting pressure on the wrench handle back n forth till loosened, watch where u put your fingers when doing all this, I don't want no bang " oh f k oh s t ooooooooh" good luck u can do it.
1/12/2010 11:17:05 PM •
Hand Tools
•
Answered
on Jan 12, 2010
•
310 views
Need owners manual Triton 2000 work bench
just go to the
www.triton.com web site under downloads go to the triton2000 manual # PUA285 go to order parts & order the PUA285 you can do this just follow the promts, looks like a nice porto tool, good luck johnnyo5n27
1/12/2010 10:25:10 PM •
Hand Tools
•
Answered
on Jan 12, 2010
•
468 views
How to change brushes on a sears wood router?
if it's older the procedure should present it self clearly,....if it's newer they are no longer made to be fixed,......getting brushes for this (if newer) could be nearly impossible as well,.......good luck, cracklin joe
1/10/2010 1:41:34 AM •
Hand Tools
•
Answered
on Jan 10, 2010
•
181 views
Leaking faucet
Did you check for debris, and clean it, or for deteriorated seat where cartridge washer bottoms out at tap base. If it has deteriorated too much, and seat is damaged, it won't help to replace cartridge, you will need to replace taps.
1/8/2010 4:45:09 PM •
Hand Tools
•
Answered
on Jan 08, 2010
•
257 views
Not finding what you are looking for?