20 Most Recent
MFJ 854 RF Current meter, 30mA-3A - Page 6 Questions & Answers
How to use a cen-tech stud sensor
Start where your pretty sure wall is hollow. Hold button and slowly slide side to side. When all lights light make pencil mark then start about eight inches away in same direction slide back toward pencil line and when all lights light make another pecil line the center of the two is the center of the stud.
8/4/2012 8:10:21 AM •
Hand Tools
•
Answered
on Aug 04, 2012
Will the charge light on my kawasaki 19.2 volt
Generally lights stop blinking when charged but not sure on Kawasaki. If that was a comment against ryobi its not the top of the line but it will drill circles around a Kawasaki. Kawasaki great if it takes gasoline. Cordless tools not so good..
8/4/2012 8:05:45 AM •
Hand Tools
•
Answered
on Aug 04, 2012
Have a Panasonic 10.8v cordless impact. Batteries
Buy a new one. Panasonic does not make good cordless tools and if you got over a year out of it feel lucky. Not being sarcastic at all. The batterys go and there not worth replaceing.. Ken
8/4/2012 8:00:15 AM •
Hand Tools
•
Answered
on Aug 04, 2012
Directions for Arrow JT-21 staple gun
The jt 21 is that little red one, I have one in my shooting box, only takes the jt staples, and operates just like any staple gun. Feed it from the back.
10/28/2011 8:31:08 AM •
Hand Tools
•
Answered
on Oct 28, 2011
I AM TRYING TO REGISTAR
go to blackanddecker.com and in the header area towards the right is an icon for registering tools. If you still have a problem let me know and I will find another way into their site.
9/11/2011 3:42:57 AM •
Hand Tools
•
Answered
on Sep 11, 2011
SEVERAL OF MY HAND TOOLS
Hi, this is normal. You can reduce it by blowing them out occasionally with an air compressor. Hope this helps, regards Phil.
8/29/2011 12:19:55 PM •
Hand Tools
•
Answered
on Aug 29, 2011
I ordered a keyless chuck
you would have to call the place where you ordered the chuck from to find this information and also the place where your drill is, I would have thought that them being a service center they would have one or taken care of the ordering for you or at least that is the way I do it..
8/16/2011 12:47:08 PM •
Hand Tools
•
Answered
on Aug 16, 2011
Crankshaft damper turning tool
In a pinch, don't have the right tool, take an old serpentine belt,<br />
<br />
cut it to fit around the damper plus about 4inches on each side,<br />
<br />
take some welders c clamp pliers and pinch the serpentine belt<br />
<br />
close to the damper, now you have a handle to turn as well as<br />
<br />
leverage. good luck!
My trimmer/edger cordless 18 volt
Chances are it is a bad charger. If you contact the manufacturer they may have a local service center you can bring the charger & batteries to get tested.
If you have any more questions or need help getting a manufactuers contact info please ask. If you feel I have helped answer or resolve your issue, please rate me. Thank you
7/5/2011 3:36:26 PM •
Hand Tools
•
Answered
on Jul 05, 2011
Magnetize your screwdriver
Here's a simple tip on how to keep from dropping those small or any screw that is in a tight place as you remove it.<br />
<br />
Take any kitchen magnet that you have on the fridge and remove the little dot magnet off of the back. Place the magnet up close to the handle of the screwdriver and there you have it. It'll be strong enough to hold the small screw to the screwdriver so you can remove it without dropping it!<br />
<br />
You can buy the magnet(s) from the Dollar Store or anywhere else....or pick some up from a yard/garage sale...such as the kids little alphabet letters with the small dot magnet on it.
STIHL TS 400 won't start
I just repaired one with a similar problem--not getting enough gas. Two things corrected it and both were carb related. First I replaced a rather stiff diaphragm with a new one and second I reset the intake valve to allow more fuel into the carb. That solved it. Good luck.
The gas filter is weighted and should remain at the low point in the tank so it is an issue only when you are about to run out of gas--unless gas has been sitting in the tank for a long time. That can leave a film on the filter that can restrict fuel flow. Pull the fuel filter from the tank and scrap lightly on the filter. You will immediately note if there is a film on it. If so, replace the fuel filter.
4/22/2011 6:46:21 PM •
Hand Tools
•
Answered
on Apr 22, 2011
Not finding what you are looking for?