20 Most Recent
Sharp AL-1641CS Laser Digital Copier - Page 3 Questions & Answers
Service tech's window on a Sharp AR-C260P
You mast remoove 4 screws and take off the back cjver of the mashine
2/ To be shjre? that? tere are no the some cutting peaces of the paper
3. See the papers flag is on correct and did not brocen with the remooving paper///
4/ There are no any coode to reffreshing this mistake
5 you mast visual observe fixin exit unit///
6 it is very ofen problem in copiers and printers///
7 If you a shore? thet the fla jf mooving papar is well, yours machine mast to work well
Good luck!
"P" is blinking in display Sharp AL-1641cs
There is a small white gear that drives the fuser module. It wears out at 30 to 40 thousand pages.
If the sound is a jumping to gringing noise that would be the problem.
That gear jumping will cause the machine to say out of paper,, jam,, give all kinds of problems from things bouncing around.
Sharp AL-1641CS Copier Manual Download
Free Sharp AL-1641CS Copier Manual DownloadModels: Sharp AL-1632 / Sharp AL-1641CS
Would
you like to review the features of the Sharp AL-1641CS Copier?
Have
you lost your Sharp AL-1641CS Copier Owner's Guide?
Would
you like a free digital, searchable, pdf version of the Sharp AL-1641CS Copier Manual?
Follow this link (& click
FREE)
to download a pdf version of the Sharp AL-1641CS Copier
documentation.
I hope that helps.
___________________________________________________
MY AL-1641CS LEAVES A THICK LINE ON THE PAPER. I
If the drum is rotated in the proper direction, it should be clean. If the line on your copy is in about the same location from to back as the line on the drum then your only option is going to be to replace the drum unit. The drum unit contains a drum cleaning blade that is supposed to clean the drum as it is being rotated. This is apparently not working in your case. These cleaner blades can be replaced if you have someone locally that can do it. The cost of a cleaner blade is about $20.
Good Luck and Thank You for using Fixya.
Loud popping sound. can see gears jumping in back
You need to replace the fuser driver gear. You can order in on line. The correct name for the gear is called a Rachet Gear... That's the easy part... changing it is another story.... It is not real easy...It may be beyond your techical skill and may have to call a service tech ??Good Luck
Driver
it doesn`t work with win7.applly winXP then install it.
I have a Sharp AR250 Copier that got the H5-01
Hello.
Yes .. that machine doesn't have a " * ", so press the Interrupt
button instead of the " * ".
So it was P
interrupt C interrupt 14 start, press execute - on screen. Then, turn the machine OFF and back ON and code should be cleared.
The icon for the interrupt button looks like
two horizontal lines with an arrow pointing from right to left between the lines.
Hope this helps.
Geting code L 1 unit will not do any thing
Scanner movement failure. The scanner is the part under the glass that lights up and moves back and forth. So if you lift up the feeder so you can see the glass, turn the machine off for a few seconds then back on. Watch the movement of the scanner. It should move right and inch or two then back to the left. If all goes well the copier should come to ready. Lay a piece of paper on the glass and press the print button to watch the scanner movement. If it binds up or does not scan correctly there are 2 possibilities.
1) your scanner lock is engaged and is preventing the scanner from moving. Check the clear plastic dial located under the far left upper side of the copier, near where the paper exits the machine. Make sure it is in the unlocked position.
2) Your scanner rail is dirty and dry. This rail can be seen under the glass towards the back of the copier. The scanner rides on this rail. It is very common for these to get dirty and for the grease to dry up causing the scanner to freeze up on the rail. The glass must be removed and the rail cleaned and lubricated.
Just
power off then on the copier to reset.
What does the error message
please check the subcode by pressing 0 key ,L means ,may be from lens area , or main motor area have problem
Hello:
Please Check the Main motor /Main drive section ( main drive gear unit) if not solve
contact
[email protected]
088-01710 950340
Do you know how to reset the drum counter for
Reset the drum count by pressing "Clear" then "Exposure Mode" then "Clear" then "Exposure Mode"
Exposure mode is far left key on panel. You need to do this fairly quickly so that the display goes blank.
Once display goes blank then key in 24 then press print, then key in 7 then press print. You should now be getting flashing 000
Turn machine off then on and light should be gone.
Short version: C,far left,C,far left,24,print,7,print
Not finding what you are looking for?