Top 20 Peavey PR15 400w PA Speakers - Page 3 Questions & Answers

if the wires are sodered on to yhe ends of the fuse you can carefully cut them right at the fuse but i would hold my sodering tip on the weld and pull the wire off when the solder melts. Unfortunatly you would have to solder a new fuse back in being realy,really carefull about how long u leave the heat on as it could cook the fuse Sounds like a job for a repairman as you dont want to be frying anything else or altering a good amp and if they screw it up they have to take care of it. please let me know how it goes,im curious.

It is possible that you have issues with caps in the power supply...I would check those first...and you can get the schematics from Peavey....

Try to find a new board. Trust me, you are not going to fix it - there is a reason the traces and board are showing burn marks. Either scrap it or just buy another one. If you toss it cut the power cord off next to the chassis.

Hi Elijah, check that you have assigned the channels to a SubMaster to the Master and that they are not in MUTE Hola Elijah, controla que tengas asignado los canales a un SubMaster al Master y que no se encuentren en MUTE https://peavey.com/products/index.cfm/item/666/118299

Contact Peavey...They have no problem in releasing technical documentation....I always get info from Peavey...

Have you tried contacting Peavey??

Hello John, the fuse is in the power input of Tu Peavey If you notice, on the rear panel, where the power cord is plugged in, up on the same connector, you will see a horizontal cover that can be removed by placing a tip on the underside of this cover and pulling outwards, it will come out a plastic element, which holds the fuse, this element has an intermediate space where another spare fuse can be housed I hope my comment has been useful and you can take out the fuse Keep in mind that if you blow the fuse, because I pass, check the cables and speaker connectors, that do not have any short circuit Greetings Franco Dosil Hola John, el fusible se encuentra en la entrada de energ?a de Tu Peavey Si te fijas, en el panel trasero, donde va enchufado el cable de corriente, arriba en el mismo conector, vas a ver una tapa horizontal que se puede sacar poniendo una punta del lado de abajo de esta tapa y haciendo fuerza hacia afuera, saldr? un elemento pl?stico, que sostiene al fusible, este elemento tiene un espacio intermedio donde se puede alojar otro fusible de repuesto Espero que te haya servido mi comentario y puedas sacar el fusible Ten en cuenta que si se quemo el fusible, porque paso,revisa los cables y los conectores de parlante, que no tengan ning?n cortocircuito Saludos Franco Dosil https://www.google.com/url?sa=i&source=images&cd=&ved=2ahUKEwiUpJWv4bDiAhUTIrkGHXfyDoQQjRx6BAgBEAU&url=https%3A%2F%2Fwww.tme.eu%2Fhtml%2FES%2Fconectores-machos-iec-con-proteccion-de-fusible-para-panel-schurter%2Framka_3250_ES_pelny.html&psig=AOvVaw3u39E87rodMysi11CwjaR6&ust=1558670267837577

I would think you can if the amp is rated for 4 ohms but the 4 ohm might be loader then the 8 ohm because it will get more power.

https://amprepairparts.com/peaveyschem.htm

You could try Googleing it, if you havn't already. Another method I've used on other guitars was to carfully remove the neck from the rest of the guitar. Manufacturers often put the production year on a tag or even printed directly on the wood body under the interfacing part of the neck. Some risk= "what if I damage my guitar?"

you could have blown a resistor or transistor since it's not a tube amp.

Probably 1997

Yes..these amps due have fuses. Check to make sure the fuse is good, it should be close to the power cord in the back under a small, black, screw on type knob. You should also check the power on/of switch and power cord for issues.

Hi! Contact Peavey Support peavey com Peavey com

Turn your guitar away from the amp's speakers. The pickups on the guitar are feeding the amp's signal back into the amp creating a feedback loop, especially with the gain button on. Loud volumes cause this looping path between the amp speakers and guitar pickups. You may need to reduce amp volume also.

What kind of casters are you installing? There are two types, ones that have a shaft sticking up from the base and ones that only have the flat base with four screw holes - I recommend using the flat base ones. There is no real easy way to open up the bottom of the cabinet as it is glued and then covered with the tolex or similar material. If you have the ones with a shaft I recommend getting the other type. The shaft has a socket you have to install in the bottom which makes them removable. There is no reason to remove the casters so get the ones that are screw mounted.

1993

https://assets.peavey.com/literature/manuals/80361051.pdf

fixya doesnt do appraisals bring to a music or pawn shop

https://r.search.yahoo.com/_ylt=Awr9DtVGSN5bJo8AUtZXNyoA;_ylu=X3oDMTByNDZ0aWFxBGNvbG8DZ3ExBHBvcwM2BHZ0aWQDBHNlYwNzcg--/RV=2/RE=1541322950/RO=10/RU=https%3a%2f%2felektrotanya.com%2fpeavey_kb2.zip%2fdownload.html/RK=2/RS=v0cqyXdd15jxSmLgvz06.J9xeZ8- This is the link to the service manual. Sounds like the power transistor is failing.