Top 20
Canon FAX-L800 Plain Paper Laser - Page 8 Questions & Answers
How do you install a timing strip inside of a Canon 5220 Printer?
Installing a timing strip in a Canon 5220 printer can be a bit of a tricky process, and it's important to follow the instructions carefully to ensure that the strip is installed correctly. Here are the general steps for installing a timing strip in a Canon 5220 printer:
- Turn off the printer and unplug it from the power source.
- Remove the toner cartridge and any other cartridges or components that are in the way of the timing strip.
- Locate the timing strip. It is usually a thin strip of plastic or paper that runs along the top of the printer, just behind the toner cartridge.
- Carefully remove any old timing strip that may already be in place. This can usually be done by gently pulling on the strip until it comes out of the printer.
- Take the new timing strip and align it with the grooves in the printer where the old strip was located. Gently push the strip into place, making sure that it is properly aligned and seated in the grooves.
- Reinstall the toner cartridge and any other components that you removed earlier.
- Plug the printer back in and turn it on.
- Perform a test print to ensure that the timing strip is installed correctly and that the printer is working properly.
It's important to note that the steps above are just a general guide, and the specific instructions for installing a timing strip in a Canon 5220 printer may vary depending on the manufacturer or model of your printer. Always refer to the printer's manual or consult with Canon support team before starting the process.
My new canon pixma printer TR8620 has a stuck scanner cover
I apologize for the inconvenience. Please try the following steps to open the scanner cover.
1. Unplug the printer from the power source.
2. Gently press the scanner cover at both sides and lift it upwards until it is fully opened.
3. Plug the printer back into the power source.
4. If the cover is still stuck, please contact the Canon technical support for further assistance.
Where to buy on/off switch for canon pc 400 personal copier
You can purchase an on/off switch for a Canon PC 400 personal copier from several different places. Here are a few options:
- Canon's official website: You can visit canon's official website and look for the parts store to see if they have the on/off switch available for purchase.
- Third-Party Retailers: Look for retailers that sell Canon printer parts and accessories such as Amazon, BestBuy, Newegg, and B&H Photo Video.
- Local electronics store: You can check local electronics store that sells printer parts and accessories.
- Online marketplaces: You can look for the on/off switch on online marketplaces such as eBay, Craigslist, and Facebook marketplace.
- Printer repair centers: Some printer repair centers may have the part you need, so you can check with them as well.
It's important to make sure that you're purchasing the correct part for your specific model and to buy from a reputable source.
How can you help me fix my Canon MX320? It won't work,the green and yellow light flashing and it's says 5b00 error occurred. Can you help me please!!!
- Turn off the printer and unplug the power cord.
- Open the printer cover and locate the ink absorber. It is a small, sponge-like pad that absorbs excess ink.
- Use a dry cloth to gently clean the ink absorber and the surrounding area.
- Replace the ink absorber with a new one. If you do not have a replacement ink absorber, you can purchase one from the Canon website or from a third-party supplier.
- Reinstall the printer cover and plug the printer back in.
- Turn the printer back on and test it to ensure that the error message has been cleared.
If you are not comfortable with the process or don't have the necessary replacement parts it's better to contact canon's customer support, they will guide you through the process and make sure that the issue is resolved.
Remove and clean printhead on Canon IP1300
To remove and clean the printhead on your Canon IP1300 printer, follow these steps:
- Turn off the printer and unplug it from the power outlet.
- Open the printer cover and raise the printhead lock lever.
- Lift the printhead out of the printer.
- Moisten a cotton swab with warm water and gently clean the printhead nozzles. Be sure not to touch the gold-colored electrical contacts.
- If the printhead nozzles are heavily clogged, you may need to soak the printhead in a solution of warm water and a mild cleaning agent for a few hours. Be sure to follow the manufacturer's instructions for the cleaning solution.
- After cleaning the printhead, shake it gently to remove any excess water, and then let it dry for a few hours.
- Once the printhead is dry, replace it in the printer and lower the printhead lock lever.
- Close the printer cover and plug the printer back in.
- Turn the printer on and perform a printhead alignment to ensure that the printhead is properly aligned.
If you are unable to clean the printhead or if the problem persists after cleaning, it may be necessary to replace the printhead. A new printhead can be purchased from the manufacturer or an authorized dealer.
Canon Laser shot LBP 2900B New cartridge leaked inside the printer What do i have to do now(read the Description for more information)
If a new cartridge has leaked inside your Canon Laser shot LBP 2900B printer, it is important to take action to prevent further damage to the printer. Here are a few steps you can take:
- Remove the leaking cartridge: Carefully remove the leaking cartridge from the printer and set it aside. Be sure to handle the cartridge carefully, as toner can be messy and difficult to clean up.
- Clean the printer: Use a dry cloth or cotton swabs to carefully clean any toner that has leaked inside the printer. Be sure to get into all the nooks and crannies to ensure that all the toner has been removed.
- Check for any visible damage: Inspect the printer and its components for any visible damage that may have been caused by the leaking toner. If you notice any damage, it may be necessary to have the printer serviced by a professional.
- Replace the cartridge: Once the printer has been cleaned and any damage has been assessed, you will need to replace the leaking cartridge. Be sure to handle the new cartridge carefully and follow the manufacturer's instructions for installation to ensure that it does not leak again.
I hope this information is helpful. If you have any further questions or need additional assistance, please don't hesitate to ask.
Canon ImagePrograf 750 Error: Execute printhead cleaning. If this message is still displayed, replace the printhead. Printing stopped.
It sounds like you have already tried a few steps to address the issue. Here are a few more things you can try:
- Turn off the printer, unplug it from the power source, wait a few minutes, and then plug it back in and turn it on.
- Check to make sure the printer is not in an error state. If it is, clear the error and try printing again.
- Try cleaning the print head manually. To do this, remove the print head and use a soft, lint-free cloth to clean it. You can also use a cleaning solution designed specifically for print heads.
- Check the ink cartridges to make sure they are installed correctly and have enough ink. If they are low or empty, replace them.
If none of these steps work, it may be best to contact Canon support for further assistance. They may be able to provide additional troubleshooting steps or offer a repair service for your printer.
I need a paperscasett for Canon PC-D340
A paperscasett is a tray or cassette that holds the paper in a printer or copier. If you are looking for a paperscasett for a Canon PC-D340 printer, you may be able to purchase one from Canon or from a third-party supplier. You can also try checking online retailers or office supply stores for compatible paperscasett.
To ensure that you are purchasing the correct paperscasett for your Canon PC-D340 printer, you will need to know the specific model and configuration of your printer. You may also need to consider the size and type of paper that you will be using with the paperscasett.
If you are having difficulty finding a paperscasett for your Canon PC-D340 printer, you may want to try contacting Canon directly for assistance. They may be able to provide you with more information about where to purchase a paperscasett or suggest a compatible alternative.
Why XA10 cannot power on by pressing power on button.
There could be several reasons why the Canon XA10 camera is not powering on when the power button is pressed. Here are some steps you can take to troubleshoot the issue:
- Check the battery: Make sure the battery is charged and properly inserted into the camera. If the battery is low or dead, the camera may not turn on.
- Check the power adapter: If you are using the AC adapter, make sure it is properly plugged into the camera and the power outlet.
- Try a different battery or power adapter: If you have another battery or power adapter, try using it to see if the camera powers on. If it does, the original battery or adapter may be faulty.
- Reset the camera: Remove the battery and memory card from the camera, then press and hold the power button for at least 30 seconds. Reinsert the battery and memory card, then try turning on the camera again.
- Contact Canon customer support: If none of the above steps work, the issue may be with the camera's internal components. Contact Canon customer support for further assistance.
Not finding what you are looking for?
