Top 20 Canon FAX-L800 Plain Paper Laser - Page 5 Questions & Answers

The E000202-00010 error code on your Canon IR C3226i typically indicates an issue with the Fixing Assembly Unit. You may need to replace the Fixing Assembly Unit in order to resolve this issue. Alternatively, if you are comfortable performing advanced troubleshooting with your machine, you can check the Fixing Relay PCB and check for any loose electrical connections.

You need the Software as well as the driver. https://www.google.com/search?q=canon+ir+2230+software+download ..

The printer is the Canon MF4350D Super G3 based on E-bay listings. You can find the manual at the Canon support page: https://www.usa.canon.com/support/p/imageclass-mf4350d . There is a PDF Starter Manual, manuals for the drivers (also PDF) and an e-Manual that is in a .zip file. The e-manual is most likely to have the trouble-shooting information you need. I hope this helps. Cindy Wells

Is it when you use the top document feeder? Check the scanner strip for white out of marks. https://www.google.com/search?q=Canon+iR+2230p+photocopier%2C+black+stripes ..

Question edited for full make and model details.

Error Codes > Canon > iR2420 > Code E007-0000

PrintCopy .info https://printcopy.info > model=iR2420 Code: E007-0000; Description: Fixing film sensor failure. The fixing film sensor is faulty. Remedy: - Check the connector of the fixing film sensor.

The error code E000021-0400 on a Canon C5240A typically indicates a problem with the fixing assembly temperature sensor. The fixing assembly is the part of the printer that fuses toner onto the paper, and it relies on a temperature sensor to ensure that the temperature is maintained within a certain range.

The specific error code E000021-0400 usually indicates that the temperature sensor has detected a problem with the temperature reading. This could be caused by a malfunctioning sensor, a problem with the wiring, or a problem with the fixing assembly itself.

To resolve this issue, you may need to replace the temperature sensor or the entire fixing assembly. However, before doing so, you can try resetting the printer by turning it off and on again. If the error persists, you may need to contact a qualified technician for assistance.

Print heads!

There was a posting on Fixya 10 years ago about this very situation. Rather than repeat Luke E's answer, I offer the following link: https://www.fixya.com/support/t11685564-e_screen_canon_p23_dh_v The next answer on that page will direct you to another site where the suggestion is to press the reset button on the back of the calculator. Good luck.

The Service Manual only mentions the Platen Motors, but follow the connections back to the control board and clean them with switch cleaner. Also look for any sensors that use the platen motors for functional logic decisions.

Canon imageFORMULA DR-X10C Service Manual page 164

ManualsLib https://www.manualslib.com > ... > Service manual View and Download Canon ImageFORMULA DR-X10C service manual online. ... E038. Platen motor. E040. Control PCB Sub-CPU communication failure. ..

Error code CANON iR4570/ iR3570 / iR2870 / iR2270 ' Tjah Semrawut Blog (wordpress.com)

Here is your manual. Check for paper jams. https://safe-manuals.com/user-manual/canon/mp18dii Normally the E error is caused by the printer being jammed. Press the C/CE button and check the roller with the numbers on it to be making a full turn. If it is not then try pushing the roller with the help of a rod or screw driver. The wheel should turn counter clockwise. If it is still jammed then you would need to take the unit for service to be opened and cleaned. ..

Question edited for clarity.

How to Fix Error Support Code 5b02 on Canon Printers

https://canonservice.net > How to Error 5b02 is an alarm warning for errors that occur on the printer, we have to do a reset so that the printer returns to its initial settings and Error ...

If the orange light on your Canon K10405 printer is staying on and you cannot switch it off using the on/off button, there may be a few different causes.

1. The printer may be in an error state and the light is indicating a problem with the printer. Check the printer's manual or the Canon website for troubleshooting steps specific to your printer.
2. The power button may be faulty and not functioning properly. In this case, you may need to contact Canon technical support for assistance or take the printer to a professional repair technician
3. It could be a problem with the power supply, in this case, the printer is not receiving the correct voltage, the power supply will need to be checked and replaced if necessary.
4. If none of the above steps work, the problem may be with the main board, and the machine may need to be serviced by a professional technician.

It is not recommended to pull the plug as it can cause problems with the printer's firmware and might cause more damage, instead please try the steps above before requesting service.

Error E-000602-0020 on a Canon 2425 machine can indicate a problem with the machine's hard drive. It is possible that the hard drive has become damaged or corrupted, which is causing the machine to be unable to start up properly. There are a few different steps you can try to troubleshoot this issue:

1. Restart the machine: Try turning the machine off and then back on again to see if the error message clears.
2. Check the hard drive: Make sure the hard drive is properly installed and functioning. If the hard drive is damaged or not functioning properly, it can cause the machine to display an error message and not start up properly.
3. Check for any other visible issues: Inspect the machine and its components for any visible issues that may be causing the problem. This can include debris or foreign objects that may have gotten stuck in the machine, or damage to the machine or its components.

If you have tried these troubleshooting steps and the problem persists, it may be necessary to have the machine serviced by a professional. A technician will be able to diagnose the problem and determine the necessary repairs. I hope this information is helpful. If you have any further questions or need additional assistance, please don't hesitate to ask.

There are several possible reasons why a Canon autoref thermal printer may not be printing consistently. Here are some troubleshooting steps that can help fix the issue: 1. Check the paper roll: Make sure that the paper roll is adequately loaded and aligned. If the paper is not loaded correctly, it can cause the printer to stop printing. Also, could you check if the paper roll is the correct size and type, as the printer's manual specifies? 2. Clean the print head: Over time, dust and debris can accumulate on the print head, causing it to malfunction. To clean the print head, turn off the printer and unplug it from the power source. Then, use a soft cloth or cotton swab dipped in alcohol to gently clean the print head. 3. Check the power supply: If the printer is not receiving enough power, it may not function properly. Ensure the power cord is securely plugged into the printer and the power outlet. Also, check if there are any loose connections or damaged wires. 4. Update or reinstall drivers: If none of the above steps work, try updating or reinstalling the printer drivers. Go to Canon's website and download the latest drivers for your printer model. Follow the instructions to install them on your computer. If none of these steps work for you, you can contact Canon customer support for more help.

In the link https://www.google.com/search?q=Canon+C3226i++error+code+E000202-0010 ..

Question edited for clarity.

Canon iPF5000 - Error Code: 03800500-2F30 - Printcopy.info

https://printcopy.info > code=03800500-2F30 Code: 03800500-2F30; Description: Head management sensor error. The head management sensor detected a ink discharge error. A sensor sensitivity error was ...

Error Code IPF8000 Error 03800500-2F30 - Copytechnet

https://www.copytechnet.com > ... > Canon Mar 1, 2013 - Hi My IPF8000 showing 03800500-2F30 error code. I am using this printer since 2008. Pretty familiar with the machine inside and out. Canon iPF-710 error 03800500-2F30 - Copytechnet Jul 20, 2020 Canon imageProGRAF IPF770 Nozzle POS Check Fail 2F30 ... May 2, 2018 Canon IPF 8100 errors - Copytechnet May 23, 2017 Canon IPF 8000 wasting ink and error - Copytechnet Jun 21, 2012 More results from www.copytechnet.com

Take a bottle of Isopropyl Alcohol and clean the electrical contacts on the drum and also the contacts on the machine. Bad connection. Videos as well.