20 Most Recent JVC Arsenal KD-AR5000 CD Player Questions & Answers

How can I hook up an auxiliary wire to play my IPhone on the JVC KD-AR5000

After looking up your unit's info, I found that the aux input is on the rear of the unit. Pull the unit from the dash, being careful not to disconnect any wires (sometimes the antenna adapter wire is too short and must be disconnected to work behind the unit. Just don't forget to reconnect it before putting the unit back in place). Plug one end of a 3.5mm aux cable into the aux input on the rear of the unit and feed the other end thru the hole where the unit sits in the dash and out the side of the center of the dash to either the driver or passenger footwell. Replace the head unit and GENTLY pull the rest of the slack out of the aux cable but not so hard that you disconnect it from the head unit. You can tuck any excess aux cable up under the side of the console where the plastic meets the carpet, & if you wanted to get really fancy, you could drill a slot in the storage area of the console big enough to fit the cable, but small enough so the end doesn't fall through so you could plug your phone in and hide it all in the console out of sight. Then just switch the source on the unit to aux and enjoy!

JVC Arsenal... | Answered on Jan 27, 2014

2 Answers

I have a JVC Arsenal

Yes the motor will need to be replaced and its kinda difficult to do I would leave it to a expert tech. Around $85 bucks and a lot of patients would fix this with a expert tech in this type of repair.

Since all the rest seem to work that is what it is is the motor ether jammed or burned out.

thanks hope the information helps good luck with the unit please do click the accept button for my efforts.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

JVC Arsenal... | Answered on Dec 31, 2009

1 Answer

EXAD KD - AR5000 Programming

Do you also lose your clock and radio station presets?

JVC Arsenal... | Answered on Jan 04, 2008

1 Answer

What do i connect the orange illumination wire on

Most car harnesses will correspond by Colour thus look out for an orange Colour from the pre-installed/ pre-selected wires.
Now the issue is, not all cars come with such wires pre-selected and installed ie bunched up with the Audio cluster, for such, you need to identify the wire yourself that connects to the light switch on your dash board and tap into it.

JVC Car Audio &... | Answered 2 days ago

1 Answer

I am installing a jvc radio into my 1978 cj5. I have isolated from the radio 3 wires. Battery, accessory and ground. I know where the ground goes but wonder about the other two.

the accessory wire needs to work with the key turning. the battery wire connects to the battery. if you have a volt meter it can be very easy to find your wire connections in the fuse box. find the ignition fuse in the box set your meter to volts dc take your black lead to a chassis ground and the red lead to one side of the ignition fuse turn your key to accessory and see if you get 14 volts if you do get it thats your connection. if not try the other side of the fuse.

JVC Car Audio &... | Answered on Nov 28, 2019

1 Answer

Lost security code on jvc kw radio

Press the "Hour" button (or right arrow button) to set the first and second digits of the code. Release the button once the four-digit code is accurately displayed. Press the "Mode" button to lock in the code you set. Turn the stereo deck on by pressing the "Source" or "Power" button to complete the reset.

JVC Car Audio &... | Answered on Nov 05, 2019

1 Answer

How to set clock on JVC kdsr72

http://www33.jvckenwood.com/pdfs/B5A-1265-00.pdf
(see page 4)

JVC Car Audio &... | Answered on Oct 30, 2019

2 Answers

I need to know what each pin represents on the transistor-amp.the wiring diagram to the amp itself

Contact JVC directly to request the information.

JVC Car Audio &... | Answered on Oct 28, 2019

2 Answers

My jvc kd-s27 turns on fine then goes to protect flashing will not stop or do anything else

Find and correct the problem causing it to enter protect mode.-

JVC Car Audio &... | Answered on Oct 13, 2019

1 Answer

I have a jvc KD-R370 with CD player and every time I play a cd it gets hot why?

Most likely, your engine might not be producing the correct amount of voltage to your stereo system. It's most likely being over worked, or even your CD player needs to be cleaned. If it's the latter, try a quick burst of air duster.

JVC Car Audio &... | Answered on Sep 26, 2019

1 Answer

Need JVC KD-S201 service manual or schematics, can anyone help?

https://elektrotanya.com/jvc_jr-s201_sm_en.pdf/download.html

JVC Car Audio &... | Answered on Sep 22, 2019

1 Answer

I need a wiring diagram for a JVC KDS 38 car stereo

Contact JVC directly to request.

JVC Car Audio &... | Answered on Sep 15, 2019

0 Answers

How DO I make display stationary & multicolor fuction display fo jvc kw-r910bt

JVC Car Audio &... | Posted on Sep 13, 2019 | Be the first to answer

1 Answer

Volume is low using hands free talk with JVC car radio. Model KW-V850

WHEN YOU ON A CALL YOU WILL SEE THE MIC VOLUME SETTING PUSH THE PLUS SIGN TIL VOLUME GOES

JVC Car Audio &... | Answered on Sep 12, 2019

1 Answer

How to fix jvc kds640 with no black (ground) in the wiring harness

YOU COULD TRY PLUG THE RADIO IN AND ABOUT THE YELLOW WIRE YOU PUSH A GROND WIRE INTO THE PIN HOLE AND RADIO SHOULD WORK WHEN SECURE PROPERLY

JVC Car Audio &... | Answered on Sep 12, 2019

1 Answer

No black wire in my jvc kds640 wiring harness

SEEM LIKE U GET DEFICTIVE HARNESS

JVC Car Audio &... | Answered on Sep 12, 2019

3 Answers

My JVC KD-R426 keeps on saying warning check wiring and reset system. I've tried everthing but it still does the same. What must I do

Not sure if this will help any other owners since my answer is 4 years late, but this is what I found from another user. Apparently if you mess with the wiring too often, it goes in a safe mode which you need to do some button trickery to unlock the device from it's safe mode. These are the Steps.
1.Disconnect power supply
2.Press [MENU] and [UP arrow] buttons and keep holding.
3. While holding the buttons [MENU] / [UP arrow], connect the power plug again
A. The display will show "DC ERR"
*** if it still shows "Chk wiring ..." repeat the steps above until you get "DC ERR."
4. Press [UP arrow]; the display shows "DC1 ERR"
a. Press and hold [UP arrow] and it will show "DC1 OK"
5. Press [Down arrow], the screen will show "DC2"
a. Press and hold [DOWN arrow] and the display will show "DC2 0"
6. Disconnect the power from the back of the unit.
7. Remove the Face Unit.
8. Reconnect the power from the back.
9. Use a sharp object and press the [RESET] hole for 3 seconds and release.
10. Reinstall the face unit and turn on the power.

JVC Car Audio &... | Answered on Sep 02, 2019

1 Answer

How to pair a bluotooht to my i phone i have a jvc kd-s29

Pairing Bluetooth Devices
Posters often ask "How do I pair my Bluetooth ???" Insert whatever device you have at the question marks.

Generally, you need to read the instructions for the camera, headset, speakers or whatever the Bluetooth device is.

Roughly speaking though.

Settings - Bluetooth - Search, on the Android, iPhone, Windows phone whatever.

With camera, speaker, headphones or whatever the Bluetooth device is, you have to press a button on that device to send out the signal. On my Bowers and Wilkins T6 Speakers, there is a button on the top with the Bluetooth symbol on it. This is the part people usually don't do and ask for advice, thinking it will do this automatically.

When the Android device recognises it, click Pair, and if it asks for a code, the Default is '0000', (four zeros, no quotes).

Pairing Bluetooth Devices

JVC Car Audio &... | Answered on Aug 22, 2019

1 Answer