Top 20 JVC AV-32S575 32" TV Questions & Answers

If this model has that it will be one of the rear sets of component jacks which will be marked as HD or 1080-----use the input button on the remote or the set if there to change to the correct input on the set. Hookup and select correct input.

What is on the screen?

Are you sure this is the correct model (one listed here) above?line is top top bottom or left to right and black?

013/ 054/ 055/ 060/ 065/ 067/ 089

Visit the site named 'Electro-help' for more details. Check this link and select the site named above. View it in 'Flip card' option, which can be selected from the drop down box menu at the left top corner or the display window. It will make search easy. Some times, the ads attached with each posts might help you to find the availability of spare parts. There are more than 640 posts to different brand TVs.

HelloTry these links.http://www.retrevo.com/support/JVC-AV-32S575-TVs-manual/id/279ci266/t/2/http://www.dataentryjobs.us/67948.htmlhttp://video.englishmanuals.com/crt_television/jvc/jvc_av_32s575_av32s575-171515.html

Your power supply has failed.

With TV powered ON press: [DISPLAY] and [VIDEO STATUS] on the remote at the same time.
-or- Press the [SLEEP TIMER] key and set the SLEEP TIMER for "0" MIN. While the SLEEP TIMER information is still on screen, press the [DISPLAY] key and [VIDEO STATUS] key of the remote control unit at the same time to enter the SERVICE MENU.
Exit the service menu by twice pressing the [EXIT] key on the remote.

Unless you paid for world wide warranty, the TV is only under warranty in Kuwait.
If you contact JVC.com and find a service centre near you, they will explain the system.

shut off CC.

Hello
Your TV is not getting any signal at all to process, or the tuner inside your TV is faulty. Blue back screen comes, when there is no signal to any of its input or faulty tuner. Just connect the tV with any other video source, like VCR or DVD , connected to its AV terminals and set the tV to take input AV, and check whether picutre comes in or not. If picture comes with AV connection, make sure that your tVs tuner is faulty and should be replaced. If no picutre comes with AV connections too, the Chroma Ic insie your TV is faulty, and should be replaced. OK.

Hello
Here is the procedure for auto tuning. Pleas go through it. Connect the antenna to the rear antena socket marked as &% ohms antena and continue.

If you have already run the Auto Tuner as part of the quick setup earlier in this guide, please

skip ahead to "Channel Summary" to continue setting up your television. In Auto Tuner Setup,

the TV automatically scans through all available channels, memorizing the active ones and

skipping over blank ones or channels with weak signals. This means you scan using the

CHANNEL +/- buttons), you will receive only clear active channels.

Press the MENU button

?† To AUTO TUNER SETUP

?® To operate

?® To choose CABLE or AIR

Press the OK button to start

Initial Setup

Auto Tuner Setup

Programming will take approximately 1 to 2 minutes. The auto tuner is finished when the

message PROGRAMMING OVER! appears onscreen.

Channel Summary

Channel summary allows you to customize the line-up of channels received by your TV. You

can add or delete channels from the line-up or prevent any unauthorized viewers from watching

any or all 181 channels.

Press the MENU button

?† To CHANNEL SUMMARY

?® To operate

The Channel summary screen will now be displayed with

the channels set to scan marked with an "?". You can delete

channels from the scan by removing the "?". If any channels

were missed during auto tuner setup and you wish to add

them, you may by placing an "?" next to the channel number.

?† ?® To the SCAN column

Press the OK button to include or delete from scan

Press the MENU button when finished

You can block access to a channel by activating the channel lock.

Press the MENU button

?† To CHANNEL SUMMARY

?® To operate

?† ?® To the Lock Column ( )

Press the ZERO button to lock or unlock that channel

Press the MENU button when finished

Press the MENU button when finished

AUTO TUNER SETUP
CABLE
If you wants any codes, contact me through Fixya. Ok
.
I'm quating these procedure from the manual I've with me, and it is for JVC AV32S565.

Sorry ur tv is an analog tv set u will not able to get HD on to an anolag tv set.Analog tv dosen't have the abilities to produced a high enough resolution to get a HDTV modes.U want HDTV modes,must have a LCD that have 1080i or 1080p or plama tv.

It is an indication of faulty on the vertical section. Nowadays tv will automatically shuts off if you have a problem on the vertical output I.C. to protect your tube for burning the phuspor right on the middle of the screen which will affect on the picture later on.
I've adviced you to look for a qualified technician to isolate and replaced the faulty parts and do resoldering for some dry joints because sometimes dry joints damaged the parts.
Thanks for using fixya...

its a ghot you can call ghost busters and they can get rid of it for ya. Just kidding it might be something on the inside touching eachother that shouldn't,Dust can also cause this.good luck

Prior to disassembly, unplug the power plug from the AC outlet without fail. (Turn the power "off".) Short the SB connector [1] pin and [2] pin of the DIGITAL INPUT MODULE PWB. (At the time of assembling) Before the rear cover is inserted into the cabinet,release the short-circuit between the SB connector [1]pin and [2]pin of the DIGITAL INPUT MODULE PWB. After releasing the short-circuit between the SB connectors, do not turn the power on until the rear cover is inserted into the cabinet. Negligence in carrying out the above steps may cause the inactivation of the TV.

if its wired to cable/satelite test scart leads unplugg /plug back in and if you have xbox unplug that while watching tv then plug in when u want to use it hope this helps it worked on mine

Question edited for a lot more clarity, plus Chunghop not chungCHOP :>D JVC: 089, 161, 909

CHUNGHOP Universal Remote Control Codes

codesforuniversalremotes.com https://codesforuniversalremotes.com > chunghop-univer... Jul 25, 2019 - CHUNGHOP Universal Remote Control Codes ; Aiwa: 009, 057, 058 ; Samsung: 618, 619, 620, 621 ; Philips: 013, 023, 024 ; Hisense: 676, 677, 707, 898

Question edited for clarity. If is is the outer clear screen, replace it with a a sheet of Lexan Polycarbonate sheet cut to size. Lexan is bulletproof. https://www.google.com/search?q=clear+polycarbonate+sheet+cut+to+size Sears list it but no longer available. After all Rear Projection Televisions are antique dinosaurs. Technology has moved on :>D https://www.searspartsdirect.com/model/33xrqyx4kj-001758/jvc-av-56wp74-television-parts https://www.google.com/search?q=jvc+i+art+pro+av56wp74+parts Service Manual https://www.manualslib.com/manual/2744485/Jvc-Av-56wp74.html#manual ..

Hello! If your JVC TV is displaying an onscreen remote and you're unable to use the actual remote, you can try the following steps to resolve the issue:

1. Power cycle the TV: Turn off the TV and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on. This can often reset any temporary issues and restore the functionality of the actual remote.
2. Replace the remote batteries: Check the batteries in your remote control and make sure they have enough power. If the batteries are low, replace them with fresh ones and try using the remote again.
3. Check the remote control sensor: Ensure that there are no obstructions between the remote control and the TV's remote control sensor. Clean the remote control sensor on the TV with a soft, lint-free cloth to remove any dust or debris that may be interfering with the signal reception.
4. Reset the TV to factory settings: If the issue persists, you can try resetting the TV to its factory settings. Keep in mind that this will erase any personalized settings and restore the TV to its original configuration. Refer to the user manual or the manufacturer's website for instructions on how to perform a factory reset on your specific JVC TV model.
5. Contact JVC customer support: If none of the above steps resolve the issue, it's recommended to reach out to JVC customer support for further assistance. They will have access to more specific troubleshooting steps and can guide you through the process of resolving the issue with the onscreen remote.

Keep in mind that the exact steps and options may vary depending on your specific JVC TV model. Refer to the user manual or contact JVC customer support for model-specific guidance.

1. Reset the receiver: To reset your JVC RX-5060 receiver to its factory default settings, switch off the receiver and unplug it from the power outlet. Press and hold the "Power" button on the front panel for approximately 5 seconds.Then, while still holding the "Power" button, plug the receiver back into the power outlet2.
2. Check the fuse: If your receiver still doesn't turn on, check if there's a blown fuse in the receiver.If so, replace it with a new one of the same rating3.

If none of these steps work, it's best to contact a professional or JVC's service center for further assistance. I hope this helps!