20 Most Recent Peavey SP2 PA Passive Speaker - Page 8 Questions & Answers


What is your question about the mixer?

Peavey Music | Answered on Feb 09, 2017


Pick any input channel you like and connect the sr16 with 1/4" phone3 jack cables.

Peavey Music | Answered on Feb 08, 2017


It is a 1980 model.
.

Peavey Music | Answered on Feb 02, 2017


Pedals operate at a different level then rack units that go in the effects loop.
It needs to go in front of the amp input. Guitar to pedal to amp input.

Peavey Music | Answered on Nov 13, 2016


Normally on older Peavey amps the grill is on a frame attached to the face held on with velcro. I suspect you have something vibrating against the speaker if it's only one frequency. Once the grill is off it may be apparent.
Also on old Scorpions and Black Widows Peavy has a piece of foam in the hole in the magnet to keep junk from getting in the speaker. Over time it crumbles and opens that hole, but even worse can get it the gap and freeze the voice coil. I always suggest cleaning it out while the speaker is out of the cab.

Peavey Music | Answered on Nov 13, 2016


http://www.schematicsunlimited.com/p/peavey/

Peavey Music | Answered on Oct 30, 2016


I think you may have a bad input jack, or it has come loose from the circuit board.. If you need to take it to a repair shop, ask about their bench charge. It may be cheaper to just replace the amp.

Peavey Music | Answered on Oct 07, 2016


simple !! most peavey mixers have a monitor output !! you can use that to feed new amp , and theres your volume too !!! or if your already using the monitor output , you can buy a split cable (1 in 2 outs) for main send !! this cable would have to be kept short or it will induce HUMMM !! and in real extreme cases if your using a low Z send (cant think as to why ) a device known as a (direct box) normally used by instrument sends can be used in reverse to "tap" into a low Z send and output with a unbalanced send for an amp to your other room , but hey why not just add a speaker with a volume control to it for this smaller room ? and forgo the new amp

Peavey Music | Answered on Oct 05, 2016


WHEN THE YELLOW LED IS ON ALL THE TIME, IT MEANS ITS ON PROTECTION MODE MEANSNG IT HAS A FAULT. U NEED A TECHNICIAN TO CHECK AND CONFIRM THE FAULTY COMPONENTS.

Peavey Music | Answered on Aug 26, 2016


No, not if you're used to taking mixers apart and soldering to traces. Get the schematic and parts direct fromPeavey.

Peavey Music | Answered on Jul 30, 2016


I'm pretty sure that model has active - battery powered - pickups, and yours is flat, so no output at all. The battery would be under the smaller cover plate on the back

http://resources.ibanez.com/resourceservicehost/images/Ibanez/web/insets/zoom/SR300SLB_Battery_Box.jpg

Peavey Music | Answered on Jul 11, 2016

Not finding what you are looking for?
Peavey SP2 PA Passive Speaker Logo

29 questions posted

Ask a Question

Usually answered in minutes!

Top Peavey Music Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

PNiss

Level 2 Expert

151 Answers

The Knight
The Knight

Level 3 Expert

76204 Answers

Are you a Peavey Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Peavey Music

  • Peavey Music

Most Popular Question

please send me circuit diagram qsc rmx

  • Music
Loading...