Top 20 Wolf Range WKGD-2 Gas Double Oven Questions & Answers

A plastic putty knife can help, but the logo is held on with double sided tape and the Wolf parts book always says to order a new logo whenever you order anything that requires removing the logo

need a picture, ill tell you model....... and where to order what you need

Most ovens have BAKE, BROIL and yours might have CONVECTION. Turn each on independently. If all don't work its one problem if only one doesn't its another
Also is it the gas doesn't ignite or it ignites then no temp change (or electric gets to xx degrees but doesn't get hotter?

pilots set to high

Hi

The issue can either be a bad electronic control/clock assembly or the oven temperature sensor (probe) has gone bad. To solve this issue start by checking the oven temp. sensor for 1100 ohms, if the rating is more then that then check the control and door switch and replace the part that is bad. Hope this helps...please post back for further assistance.

Daniel

we have this same issue. any resolution? we also have an erro message on the display after use sometimes randomly. Thanks!

good day,
hope this link below will solve your problem.

ovens

Wolf does not recommend use Easy Off, but this is the best cleaner for oven, just don't spray on it, wear gloves, spray on a rag and apply on to the porcelain surfaces, and other good all around cleaner is called Bar keeper's friend and you can pick it up at Safeway or ACE Hardware. Have fun.

Use de-greaser, soap, and brillo pad.

Hello, even though the igniter is glowing it does not mean it is drawing the correct amps to open the safety valve. If your igniter is glowing orange replace it. Igniters should glow brillient yellow to the point where you cant look at it. replace the igniter and you will be good to go. Good Luck!! Mike

If you have a crack, your part is no good any longer. We will be happy to send the correct part out to you asap. Just call or email us and we will be sure and get this right out to you. Is your ignitor out or another part? We hope this helps and we look forward to being able to resolve all your parts issues, so please call or email us when you are ready for our assistance.

I had the same problem with a Wolf L-Series double wall oven (Model DO30) and called for service (under extended warranty contract). The tech told me that the F1 error is a latch problem (you know the one that grabs and locks the door during self-clean cycles). He cleared the error using a series of "secret" button presses on the control panel and the problem cleared. Now, when it happens (which isn't very frequently), I do the same thing he did ... press "0" and "Temperature" for the oven causing the problem and hold them for about 5 seconds. The oven will ding and the display will show some diagnostics, including the error event. Press "Cook Time" and "Stop Time" while in this diagnostic mode to clear the error register, then press "Off". I've also tried to keep the area across the top of the oven opening clean (with a little degreaser), especially around the latch, and I've sprayed a bit of WD-40 into the latch periodically for lubrication and cleaning.

No. Because if you dont get all the cleaner off you dont know if it would be toxic or not.

Might be a bad ignition switch.

Dear Friend, Pull the oven towards you, disconnect any electrical cord from the wall. Normally the fuse is located right next where the electrical cord enter in the back of the stove. If there is any panel right on top of where the electrical cords connects to the oven, simple removed that cover and there should be a fuse. If not, removed the rear panel where the electronic control panel is. Hope you can find it! Good Luck!

you proably have an element out

model #?

how old is it? model #?

I had a Wolf 30F wall oven with a similar problemafter power outage. It wouldnt stop beeping with error message relatedto temperature control. My solution was to turn power of at circuitpanel, then reset by pressing and holding the clear button for 5seconds. Also note: in my case I had to close the displaybefore switching the panel off. When I tried to the reset process withthe panel showing, it wouldn\'t reset. To reset othervarious parts of the control panel Instructions said:Time-of-Day ClockImmediately after the oven is installed, setthe 12-hour clock to the current time of day. It may need to be resetafter a prolonged power failure. The clock is visible on the controlpanel during all modes. If the upper oven timer is set, the clock willnot be visible in the upper oven control panel display.SETTING CLOCK1) Touch CLOCK. 2) Touch number pads toset current time of day.3) Touch CLOCK or ENTER to startclock.24-HOUR CLOCKThe time-of-day clock can bechanged from a 12-hour clock to a 24-hour clock. After the clock hasbeen set, touch TEMPERATURE for three seconds, touch CLOCK, and thentouch ENTER. Follow the same sequence to change back to the standard12-hour clock setting.Fahrenheit to CelsiusTheoven can be changed from Fahrenheit (°F) temperature to Celsius(°C).

Hi

This means a loose/broken wire on the oven temp sensor or the oven temp. sensor itself is bad and should be replaced. To solve this issue test the oven temp. sensor, it should read between 1080-1120 ohms, if the rating is more then that and the door appears to be closing fine then it is the control board that is bad and should be replaced. Hope this helps...please post back for further assistance.
Daniel