20 Most Recent Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103 Questions & Answers

Wiring schematics for a Kenmore Elite heating Element can style. I have it all back together with new element now cant remember where 6 wires on the outside of casing plug into which ones?

Kenmore Elite... | Posted on Apr 29, 2017 | Be the first to answer

Reinstall diagram for Kenmore Elite Can style heating element whole assembly

Kenmore Elite... | Posted on Apr 29, 2017 | Be the first to answer

Hello, I have a Kenmore

might wanna check the connections on the back of it and make sure nothing has broken behind it....also may wanna get a mop and some towels something tells me its throwing water out the back side of itself while its running

Kenmore Elite... | Answered on Apr 16, 2017

0 Answers

At some point during the cycle a warning comes up regarding too much suds and starts to leak water. I tried draining all water and just running a cycle without soap but still had problem. My husband

Kenmore Elite... | Posted on Mar 30, 2017 | Be the first to answer

0 Answers

Kenmore Ultrwash, limited wash cycles, dishes not the best clean, red drain light on during wash

Kenmore Elite... | Posted on Mar 22, 2017 | Be the first to answer

1 Answer

Dishwasher will not start

Several things to try if you are mechanically minded. First I would pull the panel and see if you have current by testing the wires up with a meter. If you have power, at any point, look for a fuse or relay and test them. If none found, and no current found,pull the dishwasher out. Hopefully you have a 60" water line and enough drain hose that you don't have to disconnect them under the sink. Find the power line and check for voltage and the connections at the wall. I've seen bad connections a lot of times. If you do have power and good connections.let us know

Kenmore Elite... | Answered on May 11, 2016

1 Answer

My dishwasher will not allow me to hit any buttons to start the cycle,, when ever I hit the any button it flashes locked and will not start or let me cancel. How do I get it to reset?

Try power cycling, turn power off for about 15 minutes then turn on and try again.

Kenmore Elite... | Answered on Feb 06, 2016

1 Answer

No lights on Touch Pad

Sounds similar to a problem I had with mine. It just appeared to be dead even though the fuse panel wasn't tripped. The top of the dishwasher door has a little hole where with a contact inside of it and when the door is closed, it makes contact with the control panel. I blew into this little hole and like magic the machine worked. I had to try it several times and sometimes I need to use a small paint brush to clean the contact in this hole. I don't know if it's crumbs from the counter or what, but I was so relieved that I didn't call a repairman.
Good luck and let us know if this was a fix.

Kenmore Elite... | Answered on Nov 20, 2015

1 Answer

Brand new Kenmore dishwasher and it will not start. The "Locked" light keeps blinking when you try to select a cycle.

To unlock it press on the start button for 3 to 5 seconds, then select your cycle. It locks the same way.

Kenmore Elite... | Answered on Nov 20, 2015

0 Answers

Kenmore thermal fuse keeps blowing

Kenmore Elite... | Posted on Nov 18, 2015 | Be the first to answer

1 Answer

Bottom sprayer arm comes loose after each wash

What make and model number are you asking about?

Kenmore Elite... | Answered on Aug 21, 2015

1 Answer

My dishwasher says lock on hold 3 sec, how do I

Hi,
Just push and hold the lock button again till it unlocks...

heatman101

Kenmore Elite... | Answered on Jul 31, 2015

1 Answer

How do I repair the spring that holds dishwasher door?

The door spring can be seen on the side of the frame just below the bottom of the door. If the spring has just popped off you can put it back easily when the door is open. If the spring has become weak, you can get a new one from an appliance parts store or online.

Kenmore Elite... | Answered on Jun 10, 2015

1 Answer

My dishwasher will not fill

Earl,
If you have had any work done under the sink, double check and make sure the water to your dishwasher was turned back on. Assuming that the water is on, your other choices are that you have a bad water valve, which you can check if you have access to a multimeter. Set your meter to voltage, unplug the wires harness going to your water valve and if you have a knob to set your program, slowly turn that knob to where you would start the cycle and see if you get voltage when you put the probes into the wire harness. If you have voltage then the valve is bad and needs to be replaced. if you have no voltage then you may have a bad timer or control board. If you do not have a knob to set the program but push buttons instead, you basically would do the same thing to start the cycle to get those same results. Hoe this helps!

Kenmore Elite... | Answered on May 21, 2015

3 Answers

Water backs up from the drain in my dishwasher and smells. what is the problem?

Two things can cause this problem:
1. The check valve in your dishwasher may be defective, allowing water and food debris to seep (or run) back into your dishwasher.
2. Your drain hose may not be "mounted up" the way it should be. Look under your sink. Look at how your drain hose is connected to your garbage disposal. If the hose runs down to the floor of your cabinet and into your dishwasher, that is wrong. Instead, it should be mounted up so that water from the sink and garbage disposal would have to flow up first to get into the dishwasher. If you do this, then even if you have a bad check-valve in the dishwasher, it will prevent the problem (or greatly reduce the problem) of dirty water flowing back into your dishwasher.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Kenmore Elite... | Answered on May 17, 2015

1 Answer

Have kenmoore elite dishwasher model 630.13993012. have er codee01. what does it mean and can I fix it .

http://www.appliancepartspros.com/repair-help/sears_kenmore-fault-codes.html

Sears Kenmore Fault Codes AppliancePartsPros com

Kenmore Elite... | Answered on Apr 25, 2015

1 Answer

Brand new from day 1 can hear water go in doesn't seem to fill long starts wash cycle not even a minute then stops drains then shuts off

Stever,
Call where you purchased it and have them send out a service tech. Most appliances are under warranty for a year from purchase.

Kenmore Elite... | Answered on Apr 22, 2015

Not finding what you are looking for?

Popular Tags

253 questions posted

Ask a Question

Usually answered in minutes!

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103? Or just drag it here!

View Most Popular

Kenmore Dishwashers

Kenmore Dishwashers

water backs up from drain in dishwasher

Dishwashers

20 Most Recent Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103 Questions & Answers

Kenmore dishwasher 665.13763 will not start

Hello, I have a Kenmore Elite

When I turn my dishwasher on, I hear the water

Wiring schematics for a Kenmore Elite heating Element can style. I have it all back together with new element now cant remember where 6 wires on the outside of casing plug into which ones?

Reinstall diagram for Kenmore Elite Can style heating element whole assembly

Hello, I have a Kenmore

At some point during the cycle a warning comes up regarding too much suds and starts to leak water. I tried draining all water and just running a cycle without soap but still had problem. My husband

Kenmore Ultrwash, limited wash cycles, dishes not the best clean, red drain light on during wash

Dishwasher will not start

My dishwasher will not allow me to hit any buttons to start the cycle,, when ever I hit the any button it flashes locked and will not start or let me cancel. How do I get it to reset?

No lights on Touch Pad

Brand new Kenmore dishwasher and it will not start. The "Locked" light keeps blinking when you try to select a cycle.

Kenmore thermal fuse keeps blowing

Bottom sprayer arm comes loose after each wash

My dishwasher says lock on hold 3 sec, how do I

How do I repair the spring that holds dishwasher door?

My dishwasher will not fill

Water backs up from the drain in my dishwasher and smells. what is the problem?

Have kenmoore elite dishwasher model 630.13993012. have er codee01. what does it mean and can I fix it .

Brand new from day 1 can hear water go in doesn't seem to fill long starts wash cycle not even a minute then stops drains then shuts off

Not finding what you are looking for?

Popular Tags

Ask a Question

Popular Products

Kenmore 24 in. 17482 / 17484 / 17489 Built-in...

Kenmore 24 in. 15932 Built-in Dishwasher

Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Kenmore 24 in. 16032 Built-in Dishwasher

Kenmore 24 in. 15689 Built-in Dishwasher

Top Kenmore Dishwashers Experts

vince

Israel Pineiro Jr

Ron Rak

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Manuals & User Guides

Kenmore Dishwashers

water backs up from drain in dishwasher