20 Most Recent Konica Minolta magicolor 2430 DL Laser Printer - Page 4 Questions & Answers

Even if replacing the cartridge/drum didn't fix your problem, I would suggest you to check the fuser and rollers/paper pickers. Remove the Fuser unit and clean it with a lint free cloth, don't use any cleaning materials like acetone or alcohol, clean it with the cloth or a soft feather and make sure nothing is stuck on the fuser roller. The fuser unit is just above the Drum cartridge and below the Transfer belt unit. Please refer the below screenshot (no.9):


Also, clean the rollers with oil free solution like water using a soft brush or a feather. Here's an example of a roller:


Even if cleaning these components don't help, you'll need to replace or repair the Fuser unit.
Hope this helps.
Good Luck.
Thanks for using FixYa.

This means that you need to change the black toner cartridge.

It will be pace of paper inside very small, see, find it and will be print,

Send a print to the unit, open printer when paper is in drum area (guess and open a door or turn off, to stop the printer) open carefully, remove carefully and look at the paper, are the lines there, pull drum unit, flip open drum protection door if equipt, and look at the partial image on it, If the lines were imaged on the drum, replace drum unit. No marks on drum or paper yet, posible the fusing section roller is damaged and marking pages. Stop test will show where defect starts.

check the paper pick up sensor

You need to reset the "drum count" - this is normally a combination of buttons that you have to press when you have replaced the drum.
:)

http://www.precisionroller.com/4139r73500-for-konica-minolta/part_number.html

You have a faulty toner cartridge. Replace.

Open the access door press the cartridge release most likely a blue button pull it out. install the new one by sliding it in some times they are a little hard to pull out and make sure you snap it in fully close the access door and your ready to go. By the way you may want to shake the old one the say there out of toner when there are still pleant of pages that can be printed if you just shake the cartridge and reinstall it. Hope info helps.

what is an image drum? how do i tell what the part number is? and how do i change it?

Here are a couple of links from the Konica website which provide somes illustrated instructions:

Media Jam Tray 1; Paper Pickup Roller replacement instructions.


Clearing Media Jams

Replacing the pickup rollers seems like a drastic first step. I would check to make sure that the paper being used is suitable for this printer and it is in good consition. You might try a different paper to see if it makes a difference.

Good luck in resolving your issue.

Inside these machines is a rather large, black sheet that is known as the transfer belt. This belt acts to transfer the toner from the drum to the paper, Though if the outside edges of these sheet become worn or mucked up with excess toner, it will produce a copy with vertical bands of toner. In order to attempt to clean this belt, you must first shut the machine off, then open the from cover and locate the transfer belt (may need to remove the toner in order to make it visible,) then, with a damp cloth (water) gently wipe it along with the grain of the belt. Repeat this step until no residual toner appears on the transfer belt, then reconnect everything and print several test pages. If the problem does not reappear, then you are all set. However, if the dirty edges begin to come back, you will need to replace the transfer belt as the wear marks on it are trapping toner and not allowing it to be cleaned properly.

Please keep me informed on your progress and I will help the best I can.

David R.

remove the cartridges. vacuum residue. clean copper contacts on cartridges with a pencil eraser. reinstall.

2408 means that the toner cartridge you are trying to rotate to is already in the top position or you need to install another toner cartridge before you can rotate to the color you want to replace.

To fix the toner not installed message clean the three contacts on green chip on the right side of the toner cartridge. You may see black lines on them. Use an eraser or rubbing alcohol.

Hi.

Remove all paper from the printer and follow instructions below:












Here the full manual. Check from page 88.

Regards.

Ginko.

The Belt Positioning Sensor does not detect the Transfer

Belt position detection hole a second time even after

the lapse of a predetermined period of time after it has
detected one while the Transfer Belt is rotated.

It is a rack rotation failure.

• The Rack Positioning Sensor is in the blocked state

when the Rack Motor remains deenergized.

• The Rack Positioning Sensor is not blocked a second

time even after the lapse of a predetermined period of

time after it has been blocked once while the Rack

Motor remains energized.

• The Rack Positioning Sensor is unable to detect the

deceleration control position after the lapse of a given

period of time after the Rack Motor has started while

the Rack Motor is turning.

• The count value of the edge of ON signal of the Rack

Positioning Sensor during each developing positions

are not a predetermined value while the Rack Motor is
turning.

check this link for the drivers which you are looking for.
http://onyxftp.mykonicaminolta.com/download/Search.aspx