Top 20 Canon PowerShot SX130 IS Digital Camera Questions & Answers

Why not just use a USB card reader ?

This page should help you to find the right software: http://www.canon.ca/support_images/RightNow_images/Digital_Camera/D30Software_Guide.pdf And on the next link you can get all the support for the SX130 you want. Free driver, free software, free user manual. PowerShot SX130 IS

On page 69 from the manual, you find this : and here is a link to the manual. It is a PDF from Canon USA http://gdlp01.c-wss.com/gds/5/0300003855/04/PSSX130IS_CUG_EN_03.pdf

If your mode control dial is hard to rotate, there is chance that a sticky liquid may have sprayed or spilled, Take a q-tip with some rubbing alcohol or glass cleaner and rub around the outer edge, letting small amounts to slide under the dial. Begin turning the knob right away to work it in and loosen the stick. Make sure very little gets transferred from the q-tip, you don't want to short our the camera. It would be wise to do this with out the batteries loaded

ink pads on a digicam?

Canon will send you a new one for free or minimal cost. There is a pin that acts as a hinge. push it out from the side with a paperclip or very small screwdiver or punch. reinstall the new door in reverse careful of the spring. Some cameras, there's a screw holding the door on, in this case the new door will include the hinge.

This is a fixed lens camera, you cannot change lenses. If there is some problem with the camera's lens the best advice I can give you is to take it to a camera shop for repair.

Rechargeable batteries do wear out, and don't hold charge as well. It's about time to get some new batteries.

Try visiting ifixit, On ifixit.com. This site has lots of guides, video tutorials and other things that can help you when you want to repair your equipment, for free. You even can buy repair tools and spare parts. (these will cost you)

You receive a flash warning because the image does not have enough light for the aperture and shutter speed combination either you have set or the camera has set. There are several solutions. I can't seem to find whether that camera has a manual exposure mode or only auto modes. If only auto modes, refer to number 1 and the last two bullets. Solutions. 1. Turn on your flash. If you do not want to use your flash.... 2. If you have the ability to adjust your exposure settings

• Open your aperture to it's widest ability. That would be a small number like 2.8 or 3.5
• Reduce your shutter speed to about .125 Anything slower than that may introduce blur into the image depending on how steady your hands are.
• Increase your ISO upwards toward 1600. Be cautious though. The higher the ISO, the more grain or noise is introduced into the image.
• Do not use optical zoom (16x). Use only digital zoom (4x). You lose too much light at super zoom levels and the pic gets too shaky anyway.

I had a similar problem my camera kept telling me to raise the flash even when it was raised. I opened the back of the camera taking out the little screws on the back only. To the right right below the flas is a switch that registers when the flash is raised. Something had broken off in mine because nothing would push the switch. I wedged it down with a foam nose pad for glasses (came in the kit i bought for the screwdriver). Now flash registers all the time so I have to manually change the setting if I don not want flash but it is working now.

Be carefull, never use force. Check if you don't try to put in the card the wrong way around. Then check if nothing is damaged inside the memory slot. You need a bright light and perhaps a magnifying glass, because everything is very small. Compare the memory slot with a memory slot from another camera. Watch how the little knobs on the side look. I don't mean the contacts. When the contacts are bent, there is a possibility someone once pressed a memory card in the wrong way around and damaged the contacts and knob to secure the card.

Sounds like a fault in that it does not "Click"..... Take it to a repairer... UNLESS it is still under warranty in which case back to where you bought it or to Canon....

Try NOT connecting your camera to your computer. The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries. Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use any photo management program such as Picasa ( http://picasa.google.com ).

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries. Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use any photo management program such as Picasa ( http://picasa.google.com ).

Hi Louise- Nice camera! With the camera ON, click the function set wheel on the back of the camera on the right side next to the 'lightning bolt'. If you think of the wheel as a clock, touch the function set wheel at '3:00' with your nail. This will show three choices: flash automatic, flash on, or flash off. Choose 'flash on' and the camera will flash all the time. Hope this helps!

Try NOT connecting your camera to your computer. The best way to transfer pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries. Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use any photo management program such as Picasa. Organize edit and share your photos

Try NOT connecting your camera to your computer. The best way to transfer pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries. Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use any photo management program such as Picasa. Organize edit and share your photos

try a new memory card. If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_3e83613ef5f2a68b