Mitsubishi HS-U448 VCR - Answered Questions & Fixed issues


I had this problem with this specific machine. These answers have all been general to any VCR. The Mitsubishi HS-U448 has its motor underneath the machine. You don't have to remove the top cover at all. Just remove the bottom plate and spin the motor (the correct direction) to completely eject the tape.

Mitsubishi... | Answered on Oct 10, 2014 | 459 views


try press power and stop at the same time not sure what brand your vcr is.

Mitsubishi... | Answered on May 15, 2014 | 237 views


It sounds like it is set to a TV station and since all the analogue stations have now gone you will only get static. Without a remote you wan't be able to switch it. I suggest you either shop around for a replacement (try Curry's partmaster) or use a universal one.

Mitsubishi... | Answered on Jan 27, 2013 | 179 views


Not possible

Mitsubishi... | Answered on Aug 29, 2012 | 42 views


The manual is available from the Mitsubishi Support site: http://support.mitsubishi-tv.com/documents/HS-U448 . The direct link to the manual is http://support.mitsubishi-tv.com/files/oguide/HS-U448.pdf .

The original remote is no longer available. However, remotes.com has a substitute remote: http://www.remotes.com/remotes/servlet/rs?a=Search&o=c&uid=0&m=HS-U448&uuid=13065385902780 .

A number of universal remotes will probably also work. The codes will be in any remote that still controls a VCR if the remote was programmed after the HS-U448 was released.

I hope this helps.

Cindy Wells

Mitsubishi... | Answered on May 27, 2011 | 469 views


Can't be done without a remote. Most universal remotes won't change the input to L1 or L2. Logitech Harmony One works, though. It's not cheap, unfortunately.

Mitsubishi... | Answered on Jan 24, 2010 | 186 views


Take a scart cable & connect it from the VCR to AV1 on the DVD recorder. Then when you want to record from the VCR select either AV1 /EXT.1/ AUX1 on the DVD recorder as your choice of input source.It depends on the make of your DVD as to determine how the manufacturer has named this inout.

Mitsubishi... | Answered on Jun 29, 2009 | 88 views


tracking is due to rubber belts and tires being worn, look inside and replace. PRB BELTS.com google it. this can be a tricky problem if you haven't done it before.

Mitsubishi... | Answered on Apr 08, 2009 | 365 views


Hi Jaco, Have you fed in your Antenna / cable into the Rear of the VCR? And if your VCR has a Input selection switch, just check input to Tuner. You will get Blue screen if input selction is not Tuner but Camera / External source. If this does not solve your problem, then there is no Input selection happening.

Mitsubishi... | Answered on Apr 06, 2007 | 502 views


If the status LED shows a consistent green light it means that the power is on, on the TV. ... If the status LED is blinking yellow, that means the lamp cover is open. If the status LED is blinking red and then blinks yellow, that means you will need to follow that code to find the problem with the TV.Aug 14, 2013
www.youtube.com > watch

Mitsubishi DLP TV Repair - TV is Blinking - How to Identify ...


Mitsubishi... | Answered 3 days ago | 13 views


It's an antique and needs replacing.

Mitsubishi... | Answered on Jan 23, 2020 | 16 views


YOU HAVE TO SCAN FOR CHANNELS THRU THE SETUP MENU

Mitsubishi... | Answered on Jan 19, 2020 | 17 views


The main power supply regulator section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size

Mitsubishi... | Answered on Jan 13, 2020 | 82 views


TRY MITSUBISHI WEBSITE , FIXYA DOES NOT HAVE SUCH A THING OR GOOGLE

Mitsubishi... | Answered on Jan 10, 2020 | 20 views


The main problem is that you have an antique dinosaur that is well past its sell by date.

Here is an answer, but the age is the problem. An 86" Ultra HD 4K flat screen set would greatly improve your viewing enjoyment, though not the effect on your pocket!

https://techlore.com/forum/thread/21148/mitsubishi-ws-65313-will-not-come

Mitsubishi... | Answered on Jan 06, 2020 | 23 views


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty.
Counting of number of blinks to Philips TVs is entirely different to that of other brand TVs. It is not a direct count procedure. The site have details about how to count the number of LED blinks [Fault Codes] to Philips brand TVs are given; along with details of the faulty circuit location.

Mitsubishi... | Answered on Dec 15, 2019 | 41 views


CHANGE THE SLEEP TIMER TO 0

Mitsubishi... | Answered on Dec 10, 2019 | 31 views


Failing power supply

Mitsubishi... | Answered on Dec 03, 2019 | 31 views

Not finding what you are looking for?
Mitsubishi HS-U448 VCR Logo

17 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76204 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...