20 Most Recent Mitsubishi TS-5545 55" Rear Projection Television - Page 3 Questions & Answers

Maybe need new batt for remote ..try controls on set. Tv cud b worn out ...try unpluggnset for aspell n see if it reboots after a rest . Fixn it cudcost the same as new..n older tvs can hav manythings worn

try using buttons go to picture settings and turn off double screen

you can google Mitsubishi wd60638 remote they are available for $10.00 on line

try power settings see if program to go off could be going into timer mode if not bad power board

Hi Raymond....make sure the mute isn't on and internal speakers are enabled, if that checks out look at main board issues, a new board will correct your issue

This sounds like a main board issue

go into set up for picture and turn off double picture

Sorry I don't have service info on this brand

Sounds like a board issue

a local repair service

Check/replace the lamp. Clean the optics and lens assembly.

Check the power supply voltages, if good look towards a bad main

This is antique technology. https://www.google.com/search?q=Mitsubishi+dlp+tv+status+light+blinks+6+red+1+orange Make the 2 digit error code come up https://www.diyforums.net/mitsubishi-wd-65737-dlp-tv-error-codes-13203.html https://www.google.com/search?q=Mitsubishi+dlp+tv+status+light+blink+codes .. ..

If it has a HDMI input you can

If you wish to get some details; check the sites linked here. https://elektrotricks.blogspot.com/ https://electronicshelponline.blogspot.com/ Faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault. Search the site by type in the Brand Name of your set, in its search bar at the right side column, and press enter. See it in by Webview with mobile or by desktop. Mobile View has no search box. Screen-shots to defective LCD panels are given. You can see and compare to that to your TVs', and can make sure about the fault to an extent.

I think that the fuses and the circuit board and the power supply and the fuses are going bad inside of your TV and it is more convenient to purchase another TV than to try and repair your TV that is broken.

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Pull up older posts or search the site by type in the brand name of your set, at its search box at the right column.. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ https://elektrotricks.blogspot.com/ Search the site by type in the brand name of your set, in its search bar at the right side column, and press enter. See it in Webview by mobile or by desktop computer. Mobile View has no search box.

Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. https://homenol.blogspot.com/ https://elektrotricks.blogspot.com/ http://electronicshelponline.blogspot.com/ Blinking codes details to many popular brand TVs are given. If blinks continue without any pause, the main board is faulty. Search the sites by type in the brand name of your set, in its search box at the right column. View it on a desktop or in web View by mobile. Mobile view has no search box. Counting of number of blinks to Philips TVs is entirely different to that of other brand TVs. It is not a direct count procedure. The site have details about how to count the number of LED blinks [Fault Codes] to Philips brand TVs are given; along with details of the faulty circuit location.

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Pull up older posts or search the site by type in the brand name of your set, at its search box at the right column.. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ https://elektrotricks.blogspot.com/ Search the site by type in the brand name of your set, in its search bar at the right side column, and press enter. See it in Webview with mobile or by desktop. Mobile View has no search box.

usually is the power supply board. With time the whole LED array could be the problem. Needs to be replaced as a set.