20 Most Recent Mitsubishi VS-60705 60" Rear Projection Television - Page 2 Questions & Answers

You have bad capacitors in the power supply or around the 5v & 9v regulator circuits. If you have a meter just measure the outputs of the regulators. If you don't know what a voltage regulator is or does you should call a qualified repair shop. Estimate repair cost $250

do not take black box apart the front screen will lift up but do this gently and if you take the frame off the screen make sure you do not allow to bend it is plexie GLASS and will BRAKE if you need to support it put a chair in front with a pillow for the screen to sit on....be slow take your time remember to blow out dust before cleaning miorror and projectors lens then blow out just before putting front screen back, then wipe the lens again last before putting dust cover back on the lower rear.

Give it time to warm up like another 10 to 15 mins i find put a tv guide channel on the screen stays pretty much the same picture, then leave the TV on" i use a 4 hour rule if i dont view in 4 hours or more i will close tv power

Run the diaginostic that you find in the pdf user manuel...1st

The vertical and Horizontal IC's would need to be replaced on this TV. Now you can have this repaired for under $100 bucks if you know how to solder and repair this TV. But both IC's integrated circuits will need to be replaced on both horizontal and Vertical respectively.

I hope this helps you.

Please do click the accept button if this information is useful to you and have a happy Holidays. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

It may be a convergence problem...but not sure based on your description.

Here are some of the most common symptoms and example photos of a convergence problem

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.

Here are some photos of convergence problems.




Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.

SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses. Its a fairly easy DIY job or you can call in a pro. If you want to do the repair yourself check the site www.TvRepairKits.com. Their kits include a photo instruction guide, original OEM Sanyo STK chips, convergence resistors, pico fuses, thermal paste, email/phone support, etc.

Sorry,
Error code 12 means nothing is wrong, so the error code is of no help when obviously something is wrong.

Please make sure TV speaker option is ON in TV menu and replace IC301 Audio Out LA4663 on circuit board that seems bad.
Available in Part Store for $19

Above solution is for Mitsubishi VS-60705 TV as question shows, if your TV is any other model, let me know to provide you info accordingly.
Thanks.

its a click sounds of relays inside tv, please check your horizontal out transisitor if damage and replace it.

try pressing in both the menu and the input/device buttons together on the front of the set and hold for five seconds to see if the led blinks a two digit code. Then let me know the blink code.

My Mitsubishi Model VS-60705 did the same thing a couple of years ago...A TV repair facility replaced the Video card. Any repair facility that works on rear-projection TV's should be able to repair your set. I bought the set on Jan 1, 2000. Coming up on 9 years and the set works like new.

You need to take your tv in and have the picture deflector re-aligned.  This doesn't cost much, My dad had to do that to his a few months ago and it cost 30 bucks.

This sounds like one of the 9 volt regulators on the small signal board is going bad, supplying less than 8 volts. I have seen this is several of those sets. The IC needs to be replaced and if you do not have experience in servicing projection TV's then I suggest letting a qualified tech handle it for you.

minor repairings needed on main board.dry solder the main board and check for the faulty ic and replace it to solve

My Mitsubishi Model VS-60705 did the same thing a couple of years ago...A TV repair facility replaced the Video card. Any repair facility facility that works on rear-projection TV's should be able to repair your set.

I have a Mitsubishi VS-60705 and the picture flutters vertically and horizontally i need to be fixed

The picture is flipped left-to-right or is upside-down or both. This cannot happen as a result of a failure. For a CRT-based TV or monitor, it almost certainly means that the wires to the horizontal or vertical deflection yoke have been swapped to enable the picture to appear correct when viewed via a mirror (horizontal only) or if the unit were mounted base-up to a ceiling (both). The remedy is simply to swap the two wires to the relevant deflection yoke(s). There may even be obvious splices to guide you. There is usually a connector with 4 relatively fat wires that go to the deflection yoke on the CRT neck (NOT the PCB attached to the tube base). If you don't have a schematic, trace these on the main PCB back to their origin. The horizontal will originate somewhere in the vicinity of the flyback transformer. It may be possible to disengage the wires from the connector shell and swap them there. If not, cut, splice, and solder. Adjustment of the appropriate centering controls may be needed. For flat panel displays, it is even more unlikely this would happen as a result of a hardware failure. Most likely, there is a mode setting in the one of the setup menus for the TV or monitor itself. It could also be in the receiver for the TV, or the driver or application software of the PC. If the source is a video projector, the menu setting is likely there, to select between front and rear projection (horizontal) or table or ceiling mount (both). So, don't bother to open up the flat panel TV or monitor. The problem is not there! :)

Change C2C52 10uf@50v and c2p05 100uf@16v

There are two integrated circuits called convergence amplifiers , they need to be replaced. this is a common failure on this model. the cost to replace with parts is around 250.00 dls depending on the tech. if you need more help let know thanks

CHECK C2C52 10 UFD @ 50 V OFF THE BASE OF Q2C51 ON THE SIGNAL PCB. 2. CHECK C2P05 100 UFD 16 V OFF PIN 3 OF IC2P01 (9-VOLT REGULATOR) ON THE SIGNAL PCB.