Top 20
Mitsubishi WD-52725 52". Rear Projection HDTV Questions & Answers
Pictures runs of the screen
I would reset your picture settings and verify the TV box(cable SAt, etc) is sending the right formatted image. Make sure its not letterbox or 'zoom' for instance.
2/5/2016 11:02:19 AM •
Mitsubishi...
•
94 views • 0 helpful votes
Mitsubishi WD-52725 DLP DM board
The DM boards for that chassis are almost impossible to find if they are still good. Have you tried replacing the caps on the DM board that you have? Thats usually whats wrong are bad caps.
3/16/2012 4:48:33 AM •
Mitsubishi...
•
620 views • 1 helpful votes
Mitsubishi wd-52725 wont turn on. no lights,
HelloThe power regulator board of your Mitsubishi TV is faulty. There are two reasons for this fault. The fist one is with its internal protection fuse, and the second one is with component failure to the power supply board. To retify this fault, for both, you must ahve its service manual to follow. User manual provides details about how to use it; where as service manual will have all the details, circuit boards, schematic diagrams, porcieedings to take out and repair the boards, components and it values etc; I can't send the service manual to you by this window. If you want to do this work by yourself, you must have it with you, while I advice you to proceed the work. To get it, you must have to buy one amoung my service published in FixYa website, or go to Google and typw my nickname "gopakumarg43" in its search box. Click on the link "gopakumarg43 - FixYa". You can access my services there. Fixya has placed me on Google, from where you can get straight to me, by mail assistance. I can't touch you by mail, as it is against our Primium Expert's rules and regulations. The power supply of your TV should be checked. If you have knoledge in electronics and have a concept of soldering, get me by Fixya. OK.
10/23/2011 9:11:15 PM •
Mitsubishi...
•
129 views • 0 helpful votes
I have a Mitsubishi
Hello
make a System Reset process. To do this;
If the TV will not respond to either the remote control or the front panel controls and/or will not power Off, press the SYSTEM RESET button with a pointed item like the end point of a paperclip. The TV will turn Off and the TIMER light will flash quickly for about one minute. When the TIMER light stops flashing, you may again turn on the TV. The changes you made the last time the TV was on before you used the SYSTEM RESET button may be lost, however, the changes that were previously saved are not lost.
OK.
4/23/2011 5:15:51 PM •
Mitsubishi...
•
867 views • 1 helpful votes
Push on button and nothing no lights how to tell
not always but 95 percent of time if you remove the bulb the bulb will be burnt out like a regular light bulb and or shattered. At the shop the first rule was always remove the bulb and look at it. DO NOT touch the front or lense part of the bulb.
5/27/2011 10:26:49 PM •
Mitsubishi...
•
109 views • 0 helpful votes
No signals on any inputs. Menu items appear on
I suspect you have a failed main power supply, this model may not be well-protected against brownouts or surges.
The main supply is usually a separate board and if you remove the lower rear panel, look for a board that seems to be related to the AC line and has larger components than the other boards. Some of them will be cylindrical and others block-like.
Look for a board number since this is a component that is often outsourced and may not be from the same manufacturer in every set. Call the nearest service center to inquire about repair or replacement costs
6/20/2011 3:33:41 AM •
Mitsubishi...
•
41 views • 0 helpful votes
We replaced the V26 dm repair kit and the problem
Did you also replace the power capacitors on the power board. Usually the DM board and Power board caps together will cause the steady blinking led the DM caps alone only rarely cause the steady blinking led usually its a combination of both boards capoacitors failing.
2/17/2011 3:31:09 PM •
Mitsubishi...
•
659 views • 1 helpful votes
My WD-52725 mitsubishi 52 in
Hi:
This sound is an indication that the color wheel is faulty in the light engine, with mits sets you must replace the entire optics engine. You can purchased used light engines or have your sent in for repair. Try this site for rebuilt engines
www.tristatemodule.com
3/10/2011 8:02:50 PM •
Mitsubishi...
•
135 views • 0 helpful votes
Not finding what you are looking for?